A rectangular bar of length L has a slot in the central half of its length. The bar has width b, thickness t, and elastic modulus E. The slot has width b/3. The overall length of the bar is L = 520 mm, and the elastic modulus of the material is 74 GPa. If the average normal stress in the central portion of the bar is 190 MPa, calculate the overall elongation o of the bar. b 14 Answer: Ō = i 2 6/3 4/44 mm

A rectangular bar of length L has a slot in the central half of its length. The bar has width b, thickness t, and elastic modulus E. The slot has width b/3. The overall length of the bar is L = 520 mm, and the elastic modulus of the material is 74 GPa. If the average normal stress in the central portion of the bar is 190 MPa, calculate the overall elongation o of the bar. b 14 Answer: Ō = i 2 6/3 4/44 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

QUESTION 2 The rigid bar ACE is supported by two steel rods AB and CD (Esteel = 200 GPa) with the cross sectional areas of each rod is given as shown in Figure Q2. (a) Determine the position d of the 30 kN load so that the average normal stress in each rod is the same. (b) Find the strain in rod CD, ɛcD (c) Determine the horizontal displacement of point E 1.2 m ACD = 600 mm? 0.8 m E 30 kN AAB = 900 mm2 d B 1.8 m Figure Q2
A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 660 mm2. If the stress in the bar must not exceed 290 MPa and the maximum deformation in the bar must not exceed 10 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 7 m, b = 4.2 m, and c = 9.1 m.
A member is formed by connecting two steel bars shown below. Assuming that the bars are prevented from buckling sideways, calculate the magnitude force "P" that will cause the total length of the member to decrease 0.24 mm the values of elastic modulus for steel is 221 MPa. Take H1 = 4 cm, H2 is 2 x 2 cm and bottom bar (Q) is 6 x 6 cm. Also, determine the stress-induced in each section of the bar. = 9 cm, top bar (R) IP Solution: R cm x RCm Steel bar i) Magnitude Force, P = H1 cm ii) Stress-induced in the top bar = Q cm x Q cm Steel bar H2 cm iii) Stress-induced in the bottom bar =
An elastomeric bearing pad is used to support a bridge girder as shown. The bearing pad provides flexibility in the horizontal direction to accommodate thermal expansion and earthquake motions. The shear modulus of the bearing pad is G = 1.50 MPa. The beam must not displace horizontally more than 25 mm when a load of P = 45 kN is applied as shown. Determine the maximum thickness t that can be used for the bearing pad. Assume a = 300 mm and b = 420 mm. Answer: tmax = i mm
When an axial load is applied to the ends of the bar shown in the figure, the total elongation of the bar between joints A and C is 0.17 in. In segment (2), the normal strain is measured as 1,450 uin./in. Assume L₁ - 45 in. and L₂ - 94 in. Determine (a) the elongation of segment (2). (b) the normal strain in segment (1) of the bar. P A Answers: L₁ (a) in.₂ = i (b) £₁ = i B (2) L2 in. uin./in.
The stresses in a 2-D rectangular steel body (E = 200 GPa, v=0.32) are xx = -A(L - x)y, and oxy = A(h² - 4y²); other stress components are zero. Here, L represents length and h is height. What is the strain component y xy A - (h² - y²) 8E O A A 8G - (h²-x²) - (h²-x²) 8E А A= (h²-y:²) 8G ?
The aluminum bar ABC has a cross-sectional area of 20 mm2 is supported by a pin at A and a steel wire at B. If P = 50 kN calculate the horizontal displacement of P. The cross- sectional area of the wire is 1.75 mm2, modulus of elasticity of aluminum is 70 GPa and the modulus of elasticity of steel is 200 GPa. D 90 cm 90 cm B 180 cm Ale 120 cm
The rectangular bar is connected to the support bracket with a 25-mm-diameter pin. The bar width is w = 65 mm and the bar thickness is 10 mm. Each side of the bracket has the same dimensions as the bar. The average shear stress in the pin cannot exceed 115 MPa, the bearing stress in the bar cannot exceed 120 MPa, and the bearing stress in the bracket cannot exceed 140 MPa. Determine the maximum value of Pmax that can be supported by the structure. Answer: Pmax i kN
F2 Q1) Axial displacement of point C in the system shown on the left is 0.01 cm. Find the maximum elongation of the bar and the maximum normal stress. A F1 A. GIVEN: F2 = 100 kN, (1 = 240 cm, €2= 160 cm, bi = 5 cm, bz=10 cm, h=5 cm, E=2.107 N/em², a=20 cm Note: neglect stress concentration. h bị b2 A-A section
A steel bar 40 mm x 40 mm square cross-section is subjected to an axial compressive load of 200 kN. If the length of the bar is 2 m and E= 200 GPa, the elongation of the bar will be (a) 1.25 mm (b) 2.70 mm (c) 4.05 mm (d) 5.40 mm e) none of these