Question 28 Sae Answer Ir the part shown is assembled by fxed fasteners and the maximum size of the fastener is 18, what will be the required position tolerance 2 1.75 1.1 0275

Q: Liquid cooling system is advantageous because: Select one: a. It requires many components (pump,…

A: Option b is correct  Because liquid have high conductivity than air so it will be remove heat at…

Q: Find 150Am 120mm V- 100 mm

A: Consider the below diagram,

Q: Determine the forces in members CD, CJ, and DJ. M 11' A L 8' B L 6 panels at 6' K C L J D L I E L ↑…

A: To find force in member CD,CJ,DJ

Q: What minimum diameter is required for the wire?

A: Given data: -  The length of the steel wire is L = 1.95 m. The permissible elongation is δ = 0.270…

Q: Choose one of the following statements which is not true.

A: for solution refer below images.

Q: I have three parts that need to be answered pertaining to the print provided below.   What size…

A: The size of the print provided in the title box is C.Hence the correct answer is C.

Q: 2. The overhang beam is subjected to the uniform distributed load having an intensity of w = 50 kN/m…

A:

Q: You are given three metal test samples, with the same chemical composition and differing yield…

A: Given: Yield stress: A - 120 Mpa B - 140 Mpa C - 160 Mpa Grain size: A - 100 mm B - 25 mm To find:…

Q: Tolerance Maximum Limit Minimum Limit 57/8" 7'9 1/16" 16.76" 5 13/32" 7'8 15/16" 0.03" 0.007" 0.904"…

A: It is required to complete given table

Q: Limit Gauge loose fit, slide fit, easy sliding fit, running fit Go & No Go Ends O the difference…

A: As per our guidelines we are supposed to answer only one question if multiple questions are asked.…

Q: The triangular lamina with base = 80 mm, height = 60 mm.  The Iyy value is _____________ mm4 Select…

A: Given data: base (b) = 80 mm height (h) = 60 mm Need to determine the moment of inertia about y-y…

Q: R L2 (Side view) (End view)

A: Given data: α (Bend angle) =70° Kba (Strecth factor) =0.33  t  (Stock thickness) = 0.3" R (Width…

Q: machine design 1 question welding check the seam safety Example= Vd. ME Given data

A: For the given material specification, the yield and tensile stress.

Q: 5/4 Specify the x-, y-, and z-coordinates of the mass center of the quarter-cylindrical shell. 360…

A:

Q: If the pitch of a thread is 1/18 inch, how many threads are needed for the threaded section of a…

A:

Q: Calculate the linear speed of the needle at the instant that theta equals 30 degrees and the wheel…

A: To find - The linear speed of the needle at the instant that theta equals 30 degrees and the wheel…

Q: HW7_Question 4. Considering a symmetric stenosis (narrowing of blood vessel) as shown in the…

A: Data given-  Vmax at z = 0  Ro = 0.5 cm  L = 1 cm  Q = 4L / min

Q: What is the minimum distance from the holes at each end of the part? - 2x Ø 1.375-1.390 +Ø010 LABC…

A:

Q: Match the following statements with the term that best describes each statement.  hooks law creep…

A:

Q: Tolerance Maximum Limit Minimum Limit 50.7 mm 49.9 mm 26.8 cm 26.6 cm 0.04 mm 0.12 mm 258.03 mm…

A: Given data

Q: Complete an interpretation drawing that shows the required datum and the perpendicularity tolerance…

A: Perpendicularity: In GD&T the Perpendicularity is defined the two different…

Q: In charpy test specimen, the angle of v-notch section is_- O a. 60 degrees O b. 30 degrees O c. 90…

A: In the Charpy test, we measure the toughness of the material.  The angle of the V notch is 45 degree…

Q: On all CJP groove welds in butt joints transverse to the computed tensile stress, they: O A. Shall…

A: Introduction The Complete Joint Penetration (CJP) groove weld is a groove weld that extends…

Q: Compute for the value of the uniformity coefficient with the data shown below. D10 = 0.08 mm…

A: UNIFORMITY CO-EFFICIENT: It is defined as the ratio of size of opening that will just pass 60% of…

Q: (a) Figure Q5(a) shows the A kg box is held in place on the smooth bed of the dump truck by the…

A:

Q: I am going to use a Bolt through the .41 DIA holes to align the parts, answer the following: What…

A:

Q: advantage and disadvantages of using STRAIN GAUGE

A: Given: Advantage and Disadvantages of using STRAIN GAUGE

Q: 6 2 0 2 + 8- 1. Determine the area of the shape 2. Determine the moment of inertia about the y-axis.…

A:

Q: 3. If there is a 0.10 mm accuracy error for all measured parameters at Instruction 1, determine the…

A: Considering the accuracy error of 0.10 mmThen the given table values will…

Q: 2 5 What is the shape and size of this tolerance zone? 1.25 0.50 Dum +/-0.002 0.010

A: To find: The shape and size of the tolerance zone mentioned in the diagram. Tolerance: It is the…

Q: what is the length of each bar once both have been elongated

A: The area of bar A is The modulus of elasticity of A is The uniformly distributed load in bar A and B…

Q: I need help with numbers 4 and 7. They are both wrong.  One the part attached what is the maximum…

A:

Q: use 3 sig figs pls

A:

Q: What is the maximum tensile load P that can be applied to the bolted joint if the bolt diameter is…

A:

Q: 36) (SI units) A GO/NO-GO plug gauge will be designed to inspect a 60.00 +/- 0.40mm diameter hole. A…

A:

Q: Based on the part number of the vertical cylinder, look up the manufacturer’s data sheet to…

A:

Q: Is this a clearance or interference fit?

A: Clearance Fit : If upper limit of the shaft is less than lower limit of the hole, we can always have…