NOTES: ALL FILS & RNDS R.10 PART SYM ABOUT C ALL FIN. SURFACES 125/ 2.160 2X ø.188DR -0.625DRL01.000 Ø.8125-.8130 RM 2X 0.281DR |SFØ,625 V.25 2 HOLES IN LINE .720- .360 K) Ø1.36 - R3.00 H) Ø1.40 .10 .50- 1.940 .860 M) .72 .300 6Q 1.08 N 4.04 2.32 UNSPECIFIED TOLERANCESI MATERIAL THIRD ANGLE PROJECTION MALLEABLE IRON 2-PL DEC (X.XX)±.02 SCALE 1:2 DWN BY REDRAWN BY CHKD W.E.HASEK R.SCHOFIELD 3-PL DEC (X.XXX)±.005 DWG NO. TITLE 21A035 DRILLED HOLES 010 DOVETAIL BRKT -.002 ANGLE +0 30'

Q: On the attached drawing 11A005< what is dimension "G"

A:

Q: LESSON: AUTODESK FUSION 360 Identify the feature displayed in the picture, and choose from choices…

A: Identify the feature displayed in the picture, and choose from choices below.

Q: ADD MISSING LINES (VISIBLE OR HIDDEN) TO EACH OF THE PROBLEMS BELOW. XX * 30

A: Given: Photographic views: Top view, Front View and Right View.To draw: Missing lines for each…

Q: 2. Write 5 details found on the drawing title block?

A: The bottom right hand corner block in engineering drawing sheet is known as title block. This block…

Q: 3

A: intro- defects on any material is cause of failure of material.

Q: What are 1-, 2-, and 3-point perspectives? Draw cubes of different sizes using 1-, 2-, and 3-point…

A: Approach to solving the question: drawing, constructing of answer Detailed explanation: Examples:Key…

Q: able to draw the sequence chart?

A: you are asking about Sequence chart.

Q: When does the reduction in the dimensions occur?

A: Reducing of dimensions is done in the following conditions. Reducing of dimensions of a workpiece…

Q: 1- What type of drawing is this (Assembly, detail assembly, detail, pictorial)? And What is the…

A: Given Drafting To find Type of drawing Angle of projection Scale of drawing Original length of shaft…

Q: Need auxiliary views of this drawing

A: This question is based on the concept of engineering drawing.

Q: To show how individual pieces fit together, it is necessary to use larger-scale drawings and section…

A:

Q: If the part was cut by this plane, what would the resulting remaining face look like?

A: Section planes in SketchUp cut a model along a plane so you may look within it without altering…

Q: On a technical drawing, what is the difference in the application of the "cutting plane line" and…

A:

Q: Identify the following sectioning views (a, b, and c). a O Removed, Revolved and Removed O All…

A:

Q: R L2 (Side view) (End view)

A: Given data: α (Bend angle) =70° Kba (Strecth factor) =0.33  t  (Stock thickness) = 0.3" R (Width…

Q: pr... below. 5) Sketch the appropriate sectional view on the front view of the part

A: Given:To find:Sectional view on the front view.

Q: Name the feature shown below. 10 00

A: the feature displayed in the picture is extrude

Q: What is the key information that needs to be incuded in a section view on an assembly drawing.…

A: The Answer is below

Q: Write the NC part program for the part. Holes are threaded and requires two tools; T1 is a 0.5" HSS…

A: I have attached the image belowExplanation:

Q: What type of lines can be used in a drawing to show that part of an object has been removed ?

A: Solution : There are two types of line which are used to show the removed part of an object : Break…

Q: where do you get the form factor (y=.337) from? Please.

A: Form factor for full depth 20° at 24 teeth can be taken from standard table. I have provided the…

Q: can you draw the sfd and bmd please?

A:

Q: On the attached drawing, is the allowance between "shaft C" and "hole D" positive or negative?

A: Allowance is the difference between the basic dimensions of the mating parts. There are two types of…

Q: 2? Would it be .4070? Or would it be .4070/.4

A: 2) it would be .4070/.4065

Q: For the following thread designation, turns, how far have you advanced the O 083 inches O 417 inches…

A:

Q: Select the correct statement below regarding the two solid model parts shown. (A) (B) It is easiest…

A: In the figure two solid model parts are given. The extrusion is in which the two dimensional shape…

Q: 1. 1. Which part has the longest length? 2. 2. Which part has the smallest tolerance for the outside…

A: As this question contains multiple parts, solution is provided for first three parts as per policy.…

Q: What kind of information does a detail view on a drawing provide

A: A detailed drawing can be drawing of an object, assembly of multiple parts, or an entire system of…

Q: I am going to use a Bolt through the .41 DIA holes to align the parts, answer the following: What…

A:

Q: Name the feature shown below.

A: The given figure is of

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.