36) (SI units) A GO/NO-GO plug gauge will be designed to inspect a 60.00 +/- 0.40mm diameter hole. A wear allowance of 3% of the total tolerance band is applied to the GO side of the gauge. Determine the nominal sizes of the NO-GO gauge. Round your answer to the nearest thousandth of a mm

36) (SI units) A GO/NO-GO plug gauge will be designed to inspect a 60.00 +/- 0.40mm diameter hole. A wear allowance of 3% of the total tolerance band is applied to the GO side of the gauge. Determine the nominal sizes of the NO-GO gauge. Round your answer to the nearest thousandth of a mm

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter3: Job Planning, Benchwork, And Layout

Section3.1: Understanding Drawings

Problem 10RQ: List and briefly describe the three types of tolerances used on prints.

See similar textbooks

Related questions

Q: The following figure shows a balance used to measure the mass of an orange cylinder. Read the value…

A: Given Data⇒ Main scale reading=20 kg Secondary scale reading=2 unit ±1 gram tolerance has been given…

Q: If the main scale reading(mm) and vernier scale reading (division) are 11 and 15 respectively for a…

A: main scale reading = (MSR) = 11 mm vernier scale reading (VSR) = 15 mm no of division = 20

Q: Calculate the following slip gauges assemble to 100.115 mm. Use the of 1st, 2nd, 3nd & 4th to give…

A: (A) lets continuing with the slip guage' 100.115 - 1.005=99.11 99.11-9.11=90 90-90=0

Q: Tolerance note is given by: .XX ± .01 cm and .XXX ± .001 cm. What is the tolerance for a feature…

A: Given:- Tolerance note .XX ±.0.1.XXX ± 0.001To find:- Tolerance for a feature

Q: Determine the maximum deflection of the 70-mm-diameter A-36 steel shaft.

A: To find: The maximum deflection of the 70 mm diameter steel shaft. Given: The diameter of a steel…

Q: The Boss is created at 59.88, what is the allowed Position Tolerance?

A: Given data as per question Basic size of the boss =60

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: I require a gap of .03 min and .06 max between the 2.50 dim and the B dim (at the bottom). I apply a…

Q: In the following figure, add the tolerance zone and limits of size for both parts.

Q: QI) A) Fill the following blanks 1- Misalignment of measuring instrument is called 2- Applying a…

A: 1. Misalignment of measuring instrument is called Abbe's Error 2. Applying a number of known…

Q: Using the 10% rule–of–thumb for determining gagemaker’s tolerance for a plug gage, determinethe GO…

A: Given data: Calculate the maximum hole dimension as follows: Calculate the minimum hole dimension…

Q: 12) Mention two instruments used to measure internal linear dimensions.

A: Q12) Mention two instruments used to measure internal linear dimensions.,

Q: What is the philosophy of the Go and No-Gogauging? Complete any missing information on part 182 and…

A: PHILOSOPHY OF GO & NO GO GAUGING:- 1.GO end gauging :- Go end used in qualify the…

Q: A slip gauge setting height 53.155 mm is observed when a sine bar of the length 127 mm is used…

A: Angle using sine bar and slip gauge is find out by Angle = Sin-1(slip gauge height/ length of sine…

Q: If the tolerance in the figure below is for a pin .525 in diameter, what is the total positional…

Q: Select the right reading of the ?Micrometer Screw Gauge

A: we need to find reading in the micrometer.

Q: I need help with question number 15 that is pertaining to the print provided.

A: 15.The unidirectional system is used here for the dimension placing. The unidirectional system is…

Q: In pressure gages, the difference between the actual value and error value (+/-) is called…

Q: Given the measured value is 20.04mm and the true value of the measured dimensionis +-(plus minus)…

A: Firstly, we get to know about Measured value and True value: Measured value: The value which is…

Q: 13. What type of geometric tolerance has no datum features? 14. A theoretically exact dimension is…

A: As per Bartleby guidelines, this is a multipart question and we will answer the first three…

Q: 10) List three main components for the optical projector.

A: According to Bartleby's Answering Guidelines only 3 sub-questions can be answered.

Q: Identify which is the GO plug and which is the NO GO. Please explain

A: As per ISO standard design of go-no go gauge will follow as below.for solution refer below images.

Q: Tolerance Maximum Limit Minimum Limit 50.7 mm 49.9 mm 26.8 cm 26.6 cm 0.04 mm 0.12 mm 258.03 mm…

A: Given data

Q: You are given a set slip gauge containing 46 pieces of 2mm base (M46/2). Show how you would build…

Q: The least count of a micrometer is a. 0.01 mm b. 0.2 mm c. 0.05mm d. 0.1mm

A: Option a is correct.

Q: The uniform beam has a mass of 41 kg per meter of length. Determine the reactions at the supports. A…

Q: Use prefix multipliers to express each measurement without any exponents. 87.9 x 10-L

A: Given: The expression is 87.9×10-7 The scientific notification for the expression is, 87.9×10-7…

Q: For the following part sizes and geometric tolerances, determine the appropriate geometric tolerance…

A: A. Geometric tolerance = 0.005 + 0.007 = 0.007…

Q: (d) Based on the situation below, give one type of error faced by Ali's and give the suggestion how…

A: A Vernier Caliper is an instrument which is used for a variety of exact measurements. Vernier…

Q: What type of form tolerance is shown in this figure? Flatness Straightness Cylindricity…

A: Given data : Figure

Q: If the pin in the drawing below is produced at Ø.498, what is its total positional tolerance? C…

A: Given data as per the question Pin diameter =0.498

Q: dimension the distance between the holes

A: Bilateral tolerance B = 1.625T = 0.006Bilateral tolerance means that the dimension can vary in both…

Q: what are plug gauges ? how to use them to judge a qualified part?

A: Different types of gauges used in metrology are: Plug gauge Snap gauge Ring gauge Thread gauge, etc…

Q: II. Comprehensive questions. 1. Explain the meaning of the following annotations, the tolerance…

A: For solution refer below images.

Q: Refer to the Ø.750 dimension. A) Where is the tolerance specified ?…

A: 1—position 2 – the shape of the tolerance zone

Q: On attached drawing 11A017 ,What is the length of the dovetail slot? All abbreviations are…

A: In the given drawing the length of the dovetail slot is in the side view. The dovetail slot is…

Q: I need help solving problem numbers 4--15.

A: Hello, thanks for the question. Since we only answer up to 3 sub-parts, we’ll answer the first 3.…

Q: The least count of the main scale of a screw gauge is The minimum number of divisions on its…

A: As per bartleby guidelines we are allowed to solve only 1st question if multiple questions are…

Q: 31. (USCS units) A GO/NO-GO plug gage will be designed to inspect a 2.000 0.002 mm diameter hole. A…

A: Given data as per questionDimension of object to be inspected =2.000±0.002mmWear allowance…

Q: A B D (a) If the gap, w, must be at least 0.015 in for the proper functioning of the assembly, what…

Q: The least count of a dial test indicator is 0.01 mm which is a direct measurement device with 100…

A: It is required to evaluate given statement

Q: is a measure of sensitivity of a strain gauge and is represented as the ratio of to A. BSF,…

A: Strain gauges are the devices which are used to measure the stresses in equipments or parts.

Concept explainers

Limits, Fits, and Tolerances

The maximum or minimum allowable sizes within which the size of component lies are known as limits. The limits are classified into two types:

Question

36) (SI units) A GO/NO-GO plug gauge will be designed to inspect a 60.00 +/- 0.40mm diameter hole. A wear allowance of 3% of the total tolerance band is applied to the GO side of the gauge. Determine the nominal sizes of the NO-GO gauge. Round your answer to the nearest thousandth of a mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 1 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

On the toleranced rectangle below, state the tolerance within which the top surface must be flat. 1.000 1.010 1.010 1.000 There is no tolerance within which the top surface must be flat O .010
Question 3 The figures (1&2) shows a Hole-Pattern as drawn and as inspected. fill table 1 and calculate the true position tolerance. Show your calculations. Please note: Dimensions shown is relative to the actual size As drawn 4XØ0500 -0.312 Oe.005(M A BC C Pattern-4 holes # 2 1.000 # 3 +) 1.500 +)
For measuring a wire of thickness 1mm , out of a ruler, vernier calipers and Micrometer which one will be more accurate and which one will be less accurate? If the main scale of vernier calipers has calibrations, 1cm divided in two 20 divisions and the vernier scale has 10 divisions on it, what is its least count? 7. Write the correct reading of the micrometer screw gauge given in the figure. mpie 3" mark below 0 10 zero error = Correct reading = ||
36. (SI units) A GO/NO-GO plug gage will be designed to inspect a 60.00 0.40 mm diameter hole. A wear allowance of 3% of the total tolerance band is applied to the GO side of the gage. Determine the nominal sizes of the NO-GO gage. Round your answer to the nearest thousandth of a mm.
The tolerance for a ball bearing is 0.01. if the true diameter of the bearing is be 2.0 inches and the measured value of the diameter is x inches, express the tolerance using absolute value notation.
31. (USCS units) A GO/NO-GO plug gage will be designed to inspect a 2.000 0.002 mm diameter hole. A wear allowance of 5% of the total tolerance band is applied to the GO side of the gage. Determine the nominal sizes of the GO gage. Round your answer to the nearest tenth of a thousandth of a inch
Match the following term to the phrase that describes it. I had this question answered but number 3 was left unanswered. Please solve number 3 for me: "Method of expressing tolerance with a basic value".
7. This problem relates to tolerance stack-up using the absolute tolerance system, as explained in section 1-14. In the figure below, specified dimensions are as follows (all units in inches): a d 1.750 + 0.001 2.000 + 0.003 3.200 + 0.005 ?+0.010
The uniform beam has a mass of 41 kg per meter of length. Determine the reactions at the supports. A Answers: = Bx= By = i 0.00 190. i 337 2.9 m N N N 1.4 m 360 kg B
Suppose that the length of the steel bar is measured by a number of different observers and following set of 11 measurements is recorded as set A (units mm): 398, 420, 394, 416, 404, 408, 400, 420, 396, 413, 330. Next the measurements are taken using different ruler to produce measurement set B: 409, 406, 402, 407, 405, 404, 407, 404, 407, 407, 408. It can be shown that the mean values set A and B are 409 and 406 respectively. Which of the two measurement sets A and B, and the corresponding mean value, should have most confidence in? why? Text
Using the numbers from question 2, I apply a +/-.01 tol to the A dim, I apply a +/-.005 tol to the 4.00 dim. The maximum and minimum clearances I can have between the two parts is .045/.015. True or False?
The micrometre is a direct measurement device with a least count of 0.01 mm, that has 20 divisions on the thimble. Select one: True O False