What is the maximum tensile load P that can be applied to the bolted joint if the bolt diameter is 20 mm and the shear strength of the bolt material is 120 MNm 2 ? Apply a 'safety factor' of 1.2 in your calculations. Note: Please read about 'safety factors' and how they are applied in calculations. O a. 26.4 Nm2 O b. 26.4 kN O c. 62.5 kN O d. 62.5 MNm 2

What is the maximum tensile load P that can be applied to the bolted joint if the bolt diameter is 20 mm and the shear strength of the bolt material is 120 MNm 2 ? Apply a 'safety factor' of 1.2 in your calculations. Note: Please read about 'safety factors' and how they are applied in calculations. O a. 26.4 Nm2 O b. 26.4 kN O c. 62.5 kN O d. 62.5 MNm 2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The answer is one of the options below please solve carefully and circle the correct option Please write clear .
An M30 × 3.5 ISO grade 8.8 bolt is used in a joint at a preload levelrecommended for reused connections, and the joint is subject to a repeated tensilefatigue load of P = 65 kN per bolt. The joint constant is C = 0.25.a) Determine the static load factors; b) The factor of safety guarding against a fatigue failure based on the Goodmanfatigue criterion
Help !! Mechanical engineering
Just a small explanation only please and the correct answer thanks
Table 7-1 11) Determine the available tension capacity (LRFD) of the connection with A36 steel plates. Fy 36 ksi, F. = 58 ksi, U=1. Assume the bearing capacity is adequate. Available Shear Strength of Bolts, kips Nominal Bolt Diameter, d, in. Nominal Bolt Area, in.2 1.23 14 in x 1 in. R 中 Desig- Thread (ksi) | (ksi) Load- Ta ing ASD LRFD nation Cond. ASD LRFD (11) S 33.2 66.4 49.8 27.0 40.5 Group D. 99.6 41.8 62.7 34.0 51.0 D. 83.6 125 41.8 62.7 34.0 51.0 Group 83.6 125 9.5 in x 4 in. P S 51.7 77.5 155 42.0 63.0 4-1 in. A325 N bolts (Group A) (138 in. hole size) 103
The answer is one of the options below please solve carefully and circle the correct option Please write clear .
21. The operation where enlarging a hole is called (A) Reaming (B) Drilling (C) Tapering (D) Boring. 22. Temporary joint is obtained by one of the following. (A) Interference fit (B) welding (C) Riveting (D) Threaded Connection 23. The main reason for using a tensile tester is to measure the... A. ability of a metal to elongate without breaking. B. ability of a metal to bend without breaking. C. resistance of a metal against elongation when an increasing axial force is applied. D. ability of a metal to shorten without breaking. 24. The feed rate unit on lathe machine is A. Millimeter per revolution B. Millimeter per second C. Millimeter per stroke D. Millimeter 25. Why is the free-bend test used? A. To measure the ductility of weld metal B. To perform a non-destructive test C. To test the skill of a welder D. To approve welds to certain standards 26. Compressive stress can be defined or described as an internal force in a material resisting a... A. shearing load. B. pulling load. C.…
On attached drawing 11A017 ,What is the length of the dovetail slot? All abbreviations are standard
Need help typing
The answer is one of the options below please solve carefully and circle the correct option Please write clear .
TRUE OR FALSE ???
Solve the distributed load problem attached using both the calculus and the composite areas methods.