The lap joint shown is fastened by four314" dia. bolts. Assume the applied load isuniformly distributed among four rivets. Thewidth of plate is 5 inch with 1/2 inch thickand a tensile stress is 16 ksi. (assume thathole is greater than fasteners by 1/8")00a) What is the value of the externalload "P" that the plate could carry?.b) What is the shear stress of therivet?c) What is the bearing stress of theof the plate?.d) If the % bolt is replaced with 1"dia. bolt, what is the tensile stress ofthe of the plate?P.

Answered: Image /qna-images/answer/6c389226-11ae-4a65-b7a4-82320a98da83.jpg

The lap joint shown is fastened by four 314" dia. bolts. Assume the applied load is uniformly distributed among four rivets. The width of plate is 5 inch with 1/2 inch thick and a tensile stress is 16 ksi. (assume that hole is greater than fasteners by 1/8") P 00 00

The lap joint shown is fastened by four 314" dia. bolts. Assume the applied load is uniformly distributed among four rivets. The width of plate is 5 inch with 1/2 inch thick and a tensile stress is 16 ksi. (assume that hole is greater than fasteners by 1/8") P 00 00

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An aluminum structural tube is reinforced by bolting two plates to it as shown for use as a column of 1.3-m effective length. Knowing that all material is aluminum alloy 2014-T6, determine the maximum allowable centric load. (Round the final answer to one decimal place.) 6 mm 8 mm 54 mm 8 mm 8 mm 34 mm 8 mm 0 6 mm The maximum allowable centric load is 274.238 KN.
1. The frame shown is used to support a window-type air conditioning unit. It weighs 100 lbs and its equivalent weight is applied as shown. Determine the stress in the brace, the deformation of the brace when the load is applied, and the shear stress in the ¼ inch diameter bolts. 14 in 12 in 12 in Brace 1% x % inch steel angles ¼ inch bolt in single shear
B 1 boom AC is a 4-in. square steel tube with a wall thickness of 0.25 inch and the allowable stress is 25 ksi AB cable BC is 0.375 inch in diameter and the allowable stress is 18 ksi the pin at A is 0.5 inch in diameter and the allowable shear stress is 14 ksi Determine the largest safe load P. Answer in lbs. rounded-off to 2 decimal places 70° 30° 12 ft C Р 4 in. 3.5 in. Detail at A H 0.5-in. dia.
Problem 10. The A-36 steel plate has a thickness of 12 mm. If there are shoulder fillets at B and C, and O allow = 150 MPa, determine the maximum axial load P that it can support. The maximum stress at the fillets can be determined from the formula Omax = K Gave, where K is the stress concentration factor for fillets given in Graphs in Section 4.7 of Hibbeler textbook, and based on the fillet radius to small width and large width to small width ratios. Also compute its elongation neglecting the effects of the fillets. 60 mm P A B r = 30 mm 200 mm 120 mm 800 mm r = 30 mm 200 mm 60 mm P
(4) The plunger of an oil pump is held against the operating cam by a spring made of No.10 W&M gage steel wire coiled with an outside diameter of ⅞-in. There are five active coils. The open length is 1.1875in. What are the length & stress when a load of 30lb is applied.
Required information A 920-mm (4) strip of steel (E= 200 GPa) is bent into a full circle by two couples applied as shown. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. M' M mm Determine the maximum thickness t of the strip if the allowable stress of the steel is 420 MPa. The maximum thickness t of the strip is mm.
Two aluminum plates, each having a width of b = 8.0 in. and a thickness of t = 0.750 in., are welded together as shown. Assume a = 4.0 in. For a load of P = 75 kips, determine (a) the normal stress that acts perpendicular to the weld and (b) the magnitude of the shear stress that acts parallel to the weld. Answer: O= P T = 1 i 1 ksi ksi b P
Question 5 of 5 View Policies Current Attempt in Progress For the connection shown, determine the average shear stress in the 0.75-in.-diameter bolts if the load is P = 60 kips. O 27.2 ksi O 37.5 ksi O 25.8 ksi O 21.9 ksi O 35.3 ksi
A tensile force of 100 kN is applied on a 0.02-m diameter and 2-m long rod. After applying the load, the diameter of the rod decreases to 0.01998 m and the length increases to2.01 m. The true axialstrain is?
A small stepladder has vertical rails and horizontal steps formed from a C-section aluminum channel. Two rivets, one in front and one in back, secure the ends of each step. The rivets attach the steps to the left and right hand rails. A 225 lb person stands in the center of a step. If rivets are formed of 6061-T6 aluminum, what should be the diameter d of the rivets? Use a factor of safety of 8 and round your answer to the nearest 1/16 of an in.
Downvote for incorrect answer The connection is made using a bolt and nut and two washers. If the allowable bearing stress of the washers on the boards is (b)allow 2 ksi, and the allowable tensile stress within the bolt shank S is (allow 18 ksi, determine the maximum = allowable tension in the bolt shank. The bolt shank has a diameter of 0.31 in., and the washers have an outer diameter of 0.75 in. and inner diameter (hole) of 0.50 in.
Part A The strut is supported by a pin at C and an A-36 stoel guy wire AB. (Eigure 1) If the wire has a diameter of 4.8 mm, determine how much t stretches when the distributed load acts on the strut. Express your answer three to significant figures and include the appropriate unita. ? SAn = Value mm Figure 3AANm 27 m