(a) Figure Q5(a) shows the A kg box is held in place on the smooth bed of the dump truck by the cable AB. If the angle a= X°, determine the tension in the cable. The parameters A and X depend on your last digit of student's matrix number as shown in Table Q5. Q5 Table Q5 Last digit of your student's matrix number Parameter 0, 2, 4, 6, 8 1, 3, 5, 7,9 A (kg) X (*) 250 300 25 40

(a) Figure Q5(a) shows the A kg box is held in place on the smooth bed of the dump truck by the cable AB. If the angle a= X°, determine the tension in the cable. The parameters A and X depend on your last digit of student's matrix number as shown in Table Q5. Q5 Table Q5 Last digit of your student's matrix number Parameter 0, 2, 4, 6, 8 1, 3, 5, 7,9 A (kg) X (*) 250 300 25 40

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Select one: O a. X=1,498 m O b. X 0,498 m O c. X=0,754 m O d. X 0,0498 m k = m x(t) 3EI 3EI 13 13 y(t)
Determine the absolute maximum shear stress of the stress state acting on the element shown in the following figure. 120 Mpa 300 Mpa 50 Мра
Refer to the figure below. Read the feature control frame in the figure and write it out below. 0.010MABMCM
_% od 25m is 9m
use 3 sig figs pls
I am sorry but your values when plugging in are not the correct values. Not too sure where your values are from but can you please redo the question using the given values in this problem and not from a different problem please? (example, height is not 29, it is 22) all values do not correlate to this problem. I was also told when finding the area of triangle to use (1/2)*b*h*Ad^2 and not 1/36*b*h*Ad^2 Find the moment of inertia and radius of gyration of the section of this bar about an axis parallel to x-axis going through the center of gravity of the bar. The bar is symmetrical about the axis parallel to y-axis and going through the center of gravity of the bar and about the axis parallel to z-axis and going through the center of gravity of the bar. The dimensions of the section are: l=55 mm, h=22 mm The triangle: hT=12 mm, lT=19 mm and the 2 circles: diameter=8 mm, hC=6 mm, dC=8 mm. A is the origin of the referential axis. Provide an organized table and explain all your steps…
Two cylinders act right after one another. Each cylinder is metered, and some actions are slow, and there is a dwell between some actions. What is the minimum flow rate required (CFM) to operate this cylinders? (enter answer with 2 decimal places) Sequence of operations: Cyl. A extends with metering (takes 1.5 second) Dwell time for 2 seconds for part machining Cyl. B extend and retracts without metering (2 second) Dwell time for 10 seconds while an electric mixer is operated Cyl. A retracts quicky with no metering (0.5 seconds) Dwell time for 5 seconds while a part is placed before next cycle Assuming the displacements of the cylinders are: Cyl. A DE = 65 in3 Cyl. A DR = 62 in3 Cyl. B DE = 44 in3 Cyl. B DR = 41 in3
The active power is expressed in Select one: VAR None of the Answers W VA
None
Question 16 Here is a way we can estimate the distance from the earth to the moon. When the moon is seen at its zenith at a point A on the earth, it is observed to be at the horizon from point B. Points A and B are 6152 miles apart and the radius of the earth is 3960 miles. 20 Earth 0= B a) Calculate the angle in radians. (Round your answer to 5 decimal places.) d= ? v Moon Details b) Estimate the distance from point A to the moon using your angle from part a). (Round your answer to the nearest thousand.) ?
A shaft has to be assembled with a hole. The shaft has maximum limit 59.762 and minimum limit 59.56, and the hole has a maximum limit 60.24 and a minimum limit 60.04, compute the following: Tolerance of the shaft is Tolerance of the hole is Shaft size according to MMC = Shaft size according to LMC = Maximum clearance = Minimum clearance = Hole size according to MMC = Hole size according to LMC =
f) Answer the question shown in the images. Show every step