Question 1 Assume that an area is served by a three phase main feeder (K = 0.015) & two lateral (K = 0.0085) located at the end of main feeder (designated as substation A & substation B. There are 144 customers per lateral with maximum demand of 4.4 KVA / customer. The voltage are 2400/4160 V. For purposes of computing voltage drop, assume loads uniformly distributed, balanced, and a lagging PF = 0.90. Assume length main (3300 ft ) & lateral feeders (5780 ft). Note: The maximum voltage drop is calculated adding the voltage drop in the main & lateral feeder. a. Find maximum load per lateral (result must be entered in kVA)

Question 1 Assume that an area is served by a three phase main feeder (K = 0.015) & two lateral (K = 0.0085) located at the end of main feeder (designated as substation A & substation B. There are 144 customers per lateral with maximum demand of 4.4 KVA / customer. The voltage are 2400/4160 V. For purposes of computing voltage drop, assume loads uniformly distributed, balanced, and a lagging PF = 0.90. Assume length main (3300 ft ) & lateral feeders (5780 ft). Note: The maximum voltage drop is calculated adding the voltage drop in the main & lateral feeder. a. Find maximum load per lateral (result must be entered in kVA)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A single phase a. C distributor AB 300mts long if fed from end A is loaded as under a) 100amps at 0.707 p.f lagging 200mts from pointA(b) 200amps at 0.8p.f lagging 300mts from point A. The total resistance and the Reactance and the distributor is0. 2ohms and0. 1ohms per km respectively. Calculate the total voltage drop in the distributor. The load power factors refer to the voltage at the far end
pls solve in less than 30 min pls
Shown are two buses connected via a transmission line. Connected to Bus 1 is a generator(modelled as a voltage source V1), and to Bus 2 is a generator( with Voltage V2) and a load. The line impedance Z = R + jX is not known. Three-phase load is forecasted as 100MW + 60MVar. Generator at Bus 2 is scheduled to deliver 40MW and its excitation is adjusted for the machine to deliver 55 MVar. Voltage at Bus 1 is 241 KV angle 10 deg, while voltage at bus is 230 kV; use V2 as the reference for all angles. 1. What is the current (RMS) in amperes drawn by the load connected to Bus 2? 2. How much real power (in MW) is delivered by the generator connected to Bus 1? 3. What is the total real power loss along the line, in percent of the load? 4. What is the X/R Ratio of the line impedance?
QI/A: The per unit admittances are indicated at the diagram and the bus data are given in table as shown. Determine the voltage at bus 2 and reactive power at hus 3 after one iteration using suitable method. All values are in per unit. PL PG No. OL QG Angle Type 1.0 0 Slack *** 0 2 Load 0.15 0 ? 0 Gen. y=-j5 p.u y=-J2 p.u 3 3 8420 0.8 0 wwww 1.0 1.0 0.35 0 y=-32.5 p.u
The subject EE463 Power Systems analysis Please show all steps , and in clear writing it is better in hand written form.
X 0.1j Z12 = 0.1 j Z23 = 0.1 j 0.2 j KAY 02) 0.1j Load 1 Load 2 Load 3 Consider the single line diagram shown in the figure. All impedances are expressed in per unit on a common 100 MVA base. The generator transient reactance =0.5 j. The Bus 1 prefault voltage (1 + 0.0 j). If a bolted three phase fault occur at bus 1. The magnitude of fault current is: Select one O a. 5.8 pu b. 7.5 pu c. less than 5.8 pu O d. 11.6667 pu e. greater than 12.0 pu
2. A single-phase are distributor AB is fed from end A and has a total impedance of (0.3-0.3) ohm. At the far end, the voltage V-240V and the current is 100A at a p.f. of 0, 8 lagging. At the mid-point M. a current of 100 A is tapped at a p... of 0.6 lagging with reference to the voltage V_{M} at the midi-point. Calculate the supply voltage V Lambda j sending current I_{N} and the phase angle between V_{A} and V_{E}
4. A 4160V, three phase source, 4-wire supplying an unbalanced three phase load. The unbalanced connected load are: Zan = 150/53.13° ; Zbn = 150-53.13° ; Zen = 1500° Assuming positive sequence and the reference is the line voltage "a", determine: a. the line current "a" b. the line current “b” c. the line current "c". d. the total real power e. the total reactive power f. the total apparent power g. the overall power factor. h. the neutral current.
N-R
Q2\ The one-line diagram of a simple power system is shown in figure below. All impedances are expressed in per unit (pu) on a common MVA base. All resistances and shunt capacitances are neglected. The generators are operating on no load at their rated voltage. A three-phase fault occurs at bus 1 through a fault impedance of Zf = j0.08 per unit. Using Thevenin's theorem obtain the impedance to the point of fault and the fault current in per unit. Determine the bus voltages and line currents of generators during fault. X₁ = = 0.1 XT-0.1 3 1 to ojo XL=0.2 2 040 X₁ = 0.1
Referring to the circuit shown in Figure 1 below, solve the following problems: - i) Calculate the total impedance, ZT. ii) Determine the total current, Ir supplied by the generator iii) Determine the value of current at load impedance, I1, I2 and I3. iv) Calculate total real power, PT and reactive power, Qr supplied by the generator. v) Draw a power triangle of this circuit vi) Calculate the power factor of this circuit.
There is a three-phase system such that the phase current in the generator, lines and charging phase is the same. The phase voltage in the generator must be 1000 [V] with clockwise sequence. The connected load must be such that the phase current in each load is 10 [A] and its power factor is 0.97 “lagging”. a) Determine phase currents in the generator, lines and phase in the load