QI/A: The per unit admittances are indicated at the diagram and the bus data are given in table as shown. Determine the voltage at bus 2 and reactive power at hus 3 after one iteration using suitable method. All values are in per unit. PL PG No. QG Type Angle QL 1.0 0 *** 1 1.0 0.15 0 2 ? 0.8 1.0 0 + y=-j5 p.u 3 Slack Load Gen. y=-J2 p.u 3 --- 0 6820 0 www. 0.35 0 y=-J2.5 p.u

QI/A: The per unit admittances are indicated at the diagram and the bus data are given in table as shown. Determine the voltage at bus 2 and reactive power at hus 3 after one iteration using suitable method. All values are in per unit. PL PG No. QG Type Angle QL 1.0 0 *** 1 1.0 0.15 0 2 ? 0.8 1.0 0 + y=-j5 p.u 3 Slack Load Gen. y=-J2 p.u 3 --- 0 6820 0 www. 0.35 0 y=-J2.5 p.u

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The reactance diagram of the power system network is shown in figure below, where the impedance is given in p.u. Determine Z-bus matrix for the given system. i1.25 i0.5 j0.3 j1.05 Reference eee
1
Ideally, a dc load line is a straight line drawn on collector characteristic curves between which of the following? Please select one: a. Q Point and shear b. Q Point and saturation c. V_CE (interrupt) and I_C (sat) d. I_b = 0 and I_B = I_C/ß_DC
I need the answer as soon as possible
t Figure below shows a power system where load at bus 5 is fed by generators at bus 1 and bus 4. The generators are rated at 100MVA; 11 KV with subtransient reactance of 25%. The transformers are rated each 100 MVA, 11/112 KV and have a leakage reactance of 8%. The lines have an inductance of 1 mH/phase/km. Line L1 is 100 km long while lines L2 and L3 are each of 50 km in length. Load For a 3-phase fault at bus 5, the fault current is equal to 2530A. What the value of the change in the fault current if the value of the base voltage is changed to .10 kV (i.e. new value/old value) 1.0426 0.9833 1.0245 1.0166 0.9751 1
For the system shown in figure obtain the positive sequence, negative sequence and zero sequence bus impedance matrices. Data are given in table. T₁ 1 2 G₁ to Coto 4+ Item G₁ G₂ Ti T2 Line 1-2 X¹ X² xº 0.10 0.10 0.05 0.10 0.10 0.05 0.25 0.25 0.25 0.25 0.25 0.25 0.30 0.30 0.50 3 T₂ 4 340 G₂
The mathematical relationship between the voltage and current in a J-FET is a ___. a.quadratic function b.All of the above c.sinusoidal d.exponential e.linear function
following figure shows the one-line diagram of a power system. Bus 1 is selected as a reference bus (slack bus), and bus 2 is load bus. Using the Gauss-Seidel method, determine the value of the voltage at the load bus 2 and perform two iteration. Moreover determine the complex power flow at bus 1 and also active and reactive power in transmission line. The line impedance on a base of 100 MVA. Use an initial estimate of V,º = 1+ j(0) . S1 Z12 = 0.02 + j0.04 2 S2 = 280 MW +j60 Mvar
The load flow data for the sample power system are given below. The voltage magnitude at bus 2 is to be maintained at 1.04 p.u.Determine the set of load flow equations at the end of first iteration by using N-R method. Impedance for sample system Bus Code 1-2 1-3 2-3 Schedule of generation and loads: Impedances 0.08 + j0.24 line charging admittance 0.0 0.02 + j0.06 0.0 0.06 + j0.18 0.0 Bus Code Assured Voltages Generation Load MW MVAR MW MVAR 1 1.06 + j0.0 0 0 0 2 1.0 + j0.0 0.2 0.0 0.0 0.0 3 1.0 + j0.0 0 0 0.6 0.25
pls solve in less than 30 min pls
In your own word please help
Please neglect the simulation