Consider a 3-bus system of the reactive network in Figure below where bus-bar 1 is slack. Use Gauss-Seidel method to determine the voltage at bus 2 and bus 3. Compute the power at bus 1, the line flow and line loss. V₁ = 2.520° $₁ Z12 = j0.2 Z13 = j0.5 V₂ V3 S₂ = j5 S3 = j2

Consider a 3-bus system of the reactive network in Figure below where bus-bar 1 is slack. Use Gauss-Seidel method to determine the voltage at bus 2 and bus 3. Compute the power at bus 1, the line flow and line loss. V₁ = 2.520° $₁ Z12 = j0.2 Z13 = j0.5 V₂ V3 S₂ = j5 S3 = j2

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter7: Symmetrical Faults

Section: Chapter Questions

Problem 7.21P

See similar textbooks

Related questions

Q: Schering Bridge is used to find ____________. a. capacitance b. pressure c. inductance…

A: Schering Bridge is used to find ____________. a. capacitance b. pressure c.…

Q: L-type equivalent circuit and parameters for a continuous sinusoidal phase of a 5.5 kW, 1450 rpm,…

A: First we will calculate impedance ssen by the source and than we will find current from source in…

Q: L-type equivalent circuit and parameters for a continuous sinusoidal phase of a 5.5 kW, 1480 rpm,…

Q: 3 substations A, B and C are spaced 75 km apart as shown in Figure, B and C are connected together…

Q: V₁ = 120° P.U Slack bus (1) jo.05 P.U j0.2 P.U 0.4+j0.3 P.U (3) jo.025 P.U -(2) 0.8+ j0.6 P.U

Q: Calculate the initial symmetrical short circuit current that will occur when a 3 phase short circuit…

A: We can re draw the given system as Let the base MVA of the system i.e SB 500MVA and base Voltage…

Q: By using Gauss-Siedal method, the voltage of the bus 2 after two iteration is Your answer By using…

A: Given,The data of a system are,Ybus=j0.25-0.2-0.05-0.20.225-0.025-0.05-0.0250.075…

Q: The 13.2 kV 50-Hz generator feeds a load over a line with (Zload) impedance Zline. Load is 80on +…

A: Given: A 13.2 kV, 50 Hz single-phase generator supplies power to a load through a transmission line.…

Q: For the system shown in figure, voltages V2. V3 and angles 82 83 are calculated using Newton-Raphson…

A: The given system diagram is shown below,…

Q: The Gauss-Seidel is an iterative method used to solve a set of nonlinear equations in the power…

A: Gauss-Seidel method is used to solve the power flow analysis question in the power system. In two…

Q: The sample large power system network data's are given below, The total number of buses is 5…

A: There are two types of symmetrical faults: a) Three-phase short circuit fault. b) Three-phase to…

Q: The VSWR on an 50-Ohm transmission line is 5. The distance between successive voltage minima is 80…

Q: Figure below shows one-line diagram of a simple three bus power system with generation at bus 1. Bus…

A: V1= 1 pu V20 = 1+ j 0 V30 = 1+ j 0 Power at bus 2 are P2 =250 MW Q 2 =110 MVAR Power at bus 3 are…

Q: What is load curve

Q: 1. FIGURE 52 shows the one-line diagram of a simple three-bus power system with generation at bus I.…

A: Convert the line impedances into admittances, using Y=1/Z

Q: Consider the 500 kV, three phase bundled conductor line as shown in the figure below. Find the line…

Q: Q2. Figure Q2 shows the single-line diagram. The scheduled loads at buses 2 and 3 are as marked on…

A: Note: We are authorized to answer three subparts at a time since you have not mentioned which part…

Q: For the system shown in figure obtain the positive sequence, negative sequence and zero sequence bus…

Q: following figure shows the one-line diagram of a power system. Bus 1 is selected as a reference bus…

A: Solution- Given, V1 = 1 + j(0) Z = 0.02+ j0.04 p.u. S2 = 280 MW + j60 Mvar

Q: The power factor must be close to . . To insure that losses in the transmission lines will be…

A: The power factor of the system is calculated as cosine of phase angle between voltage and current of…

Q: A three-phase balanced load of 15A per phase is supplied by a steel wire armoured cable with a…

A: A three-phase balanced load is supplied with steel wire, Given Data:- mV = 15 Length of cable (L):-…

Q: 20cn) 10c2) Nodal strees Method. 50(0) 10c0) 50C 80 (A) 3 20c2) 30c2) 5CA) 5CA) 10(A) 20c2) 3 CA)

Q: 2. The one-line diagram of a three-phase power system is as shown in the figure below. Impedances…

A: In this question we need to find the voltage at bus 2 and 1. We convert all the given values in per…

Q: 7. In the circuit below write the loop equations and set up (not solve) the matrix equation for the…

Q: 2. For the 3-bus network shown in figure, the impedances indicated are in per unit. a) Draw pu…

A: given that - V1= 1∟0o V2=1.05∟90o (a) At node 1: I1 =Y1V1 + Y3 (V1-V3) + Y6 (V1 – V2) At node 2:…

Q: The steady-state voltage drop between the load and the sending end of the line seen in (Figure 1) is…

A: The given circuit diagram is shown below,

Q: The figure below shows the one-line diagram of a four- bus power system. The voltages, the scheduled…

A: Note: We are authorized to answer three subparts at a time since you have not mentioned which part…

Q: . Which one of the following method uses weak coupling between reactive power and voltage angle?. A.…

Q: In the following network, the voltage magnitudes at all buses are equal to 1 p.u., the voltage phase…

A: Given- Voltage magnitudes at all buses = 1 p.u. Voltage phase angles are small, Line resistance are…

Q: A network consisting of a set of generator and load buses is to be modeled with a DC power flow, for…

A: Given PTDF5,42-4 =-0.2609 LODF2-4,4-5 =-0.6087 Base case flow on line 4-5 is F04-5=13.6 MW Base case…

Q: in distribution transformers; What is 30 degrees phase shift in delta-star connection? What are the…

A: In the star-delta connection, the primary side of the transformer is in delta configuration while…

Q: List only TWO features of Transistor Transistor Logic (TTL) series and draw the circuit diagram of…

A: There are various categories of digital circuit, depending on different technologies. The categories…

Q: For the system shown in figure, voltages V2, V3 and angles 82, 83 are calculated using…

Q: L-type equivalent circuit and parameters for a continuous sinusoidal phase of a 5.5 kW, 1460 rpm,…

Question

Consider a 3-bus system of the reactive network in Figure below where bus-bar 1 is slack. Use
Gauss-Seidel method to determine the voltage at bus 2 and bus 3. Compute the power at bus 1,
the line flow and line loss.
V₁ = 2.520°
$₁
Z12 = j0.2
Z13 = j0.5
V₂
V3
S₂ = j5
S3 = j2

AI-Generated Solution

AI-generated content may present inaccurate or offensive content that does not represent bartleby’s views.

Unlock instant AI solutions

Tap the button
to generate a solution

Click the button to generate
a solution

SEE SOLUTION

Similar questions

Solve it quickly please
The figure below shows the one-line diagram of a four- bus power system. The voltages, the scheduled real power and reactive powers, and the reactances of transmission lines are marked at this one line diagram (The voltages and reactances are in PU referred to 100 MW base. The active power P2 in MW is the last three digits (from right) of your registration number (i.e for the student that has a registration number 202112396, P2 =396). [10] Starting from an estimated voltage at bus 2, bus 3, and bus 4 equals V2 (0) = 1.15<0°, V3 = 1.15 < 0°, V4 1.1< 0°. 1- Specify the type of each bus and known & unknown quantities at each bus. 2- Find the elements of the second row of the admittance matrix (i.e. [Y21 Y22 Y23 Y24]). 3- Using Gauss-Siedal fınd the voltage at bus 2 after the first iteration. 4- Using Newton-Raphson, calculate: |- The value of real power (P2), at bus 2 after the first iteration. Il- The second element in the first row of the Jacobian matrix after the first iteration. 2 P2…
Q2. Figure Q2 shows the single-line diagram. The scheduled loads at buses 2 and 3 are as marked on the diagram. Line impedances are marked in per unit on 100 MVA base and the line charging susceptances are neglected. a) Using Gauss-Seidel Method, determine the phasor values of the voltage at load bus 2 and 3 according to second iteration results. b) Find slack bus real and reactive power according to second iteration results. c) Determine line flows and line losses according to second iteration results. d) Construct a power flow according to second iteration results. Slack Bus = 1.04.20° 0.025+j0.045 0.015+j0.035 0.012+j0,03 3 |2 134.8 MW 251.9 MW 42.5 MVAR 108.6 MVAR
Discuss the concept of reactive power and its role in grid stability.
400Ω A k=0.9 600Ω B k=0.8 66Ω 600Ω
7. In the circuit below write the loop equations and set up (not solve) the matrix equation for the load current. Wiso 150 75 28 100
Find the following : 1.Ripple Voltage (vpp) 2. Zero-to peak ripple(Vop) 3.secondary winding of the transformer high line and low line
In the following network, the voltage magnitudes at all buses are equal to 1 p.u., the voltage phase angles are very small, and the line resistances are negligible. All the line reactances are equal to j1 p.u. (1) (2. P₂ = 0.1 p.u. P3 = 0.2 p.u. The voltage phase angle 83 in radian at bus 3 is (Assume one of the generator bus as slack bus and sin-¹ (0.1) = 0.1 rad) (a) -0.1 (b) -0.2 (c) 0.1 (d) 0
For the system shown in figure, voltages V2, V3 and angles 82, 83 are calculated using Newton-Raphson method. shunt line charging admittances are neglected. All the values are given in per unit on 100MVA base. Calculate the complex power flows S12 and S32 in actual units. 1) Z12 = 0.01+ j0.02 Z3 = 0.02+ j0.04 PL G QL Slack bus V2 = 0.96L -1.67° V3 = 0.884 - 5.48° Vi=1.0/0° (estimated time to answer this question: 13 minutes)
2. The one-line diagram of a three-phase power system is as shown in the figure below. Impedances are marked in per unit on a 100-MVA, 400-kV base. The load at bus 2 is S2 = 15.93 MW-j33.4 Mvar, and at bus 3 is S3 = 77 MW +j14 Mvar. It is required to hold the voltage at bus 3 at 4006 0 kV. Working in per unit, determine the voltage at buses 2 and 1. V3 j0.5 pu V₂ S₂ j0.4 pu S3
please explain the operating principle of single phase 2S-2P PMSM based on 3D design illustration.
Power factor correction is usually done by adding _________ to the load circuit.Select the correct response:a. switchb. capacitorc. inductive loads