following figure shows the one-line diagram of a power system. Bus 1 is selected as a reference bus (slack bus), and bus 2 is load bus. Using the Gauss-Seidel method, determine the value of the voltage at the load bus 2 and perform two iteration. Moreover determine the complex power flow at bus 1 and also active and reactive power in transmission line. The line impedance on a base of 100 MVA. Use an initial estimate of Vº =1+ j(0) . Z12 = 0.02 + j0.04 2 S2 = 280 MW +j60 Mvar %3D

following figure shows the one-line diagram of a power system. Bus 1 is selected as a reference bus (slack bus), and bus 2 is load bus. Using the Gauss-Seidel method, determine the value of the voltage at the load bus 2 and perform two iteration. Moreover determine the complex power flow at bus 1 and also active and reactive power in transmission line. The line impedance on a base of 100 MVA. Use an initial estimate of Vº =1+ j(0) . Z12 = 0.02 + j0.04 2 S2 = 280 MW +j60 Mvar %3D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

How did they get Zc=j0.43 and Zl=j0.43? How did they get the diagram break down simply?
Problem 4. A 220-kV, three-phase transmission line has a per phase series impedance z= 0.005 + O/km and a per phase shunt admittance y = j3.5x10 S/km. the line is 80 km long. The transmission line is delivering 200 MVA, 0.8 power factor lagging at 230 kV. Using the nominal pi model. d) Determine the voltage regulation and the transmission efficiency.
A 220 kV, three phase transmission line is 50 km long. The resistance per phase is r 2 per km and the inductance per phase is L mH per km. The shunt capacitance is negligible. If the line supplies a three-phase load of 229 MVA at 0.8 power factor lagging at 220 kV with an efficiency of 97.13% and a voltage regulation of 4.7581%. Use the short line model to find the line resistance and inductance of the line.
A-3-phase transmission line is shown in figure: .AV: ΔV, AVb AV -AV₂- = -AV I₁ a Ib Voltage drop across the transmission line is given by the following equation : I Z₂ Zm Zm Zm Zs Zm Zm Zm Zs ][ Ia Ib Ic Shunt capacitance of the line can be neglect. If the line has positive sequence impedance of 15 and zero sequence impedance of 48 , then the values of Z, and Zm will be S
The reactance diagram of the power system network is shown in figure below, where the impedance is given in p.u. Determine Z-bus matrix for the given system. i1.25 i0.5 j0.3 j1.05 Reference eee
1
Ideally, a dc load line is a straight line drawn on collector characteristic curves between which of the following? Please select one: a. Q Point and shear b. Q Point and saturation c. V_CE (interrupt) and I_C (sat) d. I_b = 0 and I_B = I_C/ß_DC
The load flow data for the sample power system are given below. The voltage magnitude at bus 2 is to be maintained at 1.04 p.u.Determine the set of load flow equations at the end of first iteration by using N-R method. Impedance for sample system Bus Code 1-2 1-3 2-3 Schedule of generation and loads: Impedances 0.08 + j0.24 line charging admittance 0.0 0.02 + j0.06 0.0 0.06 + j0.18 0.0 Bus Code Assured Voltages Generation Load MW MVAR MW MVAR 1 1.06 + j0.0 0 0 0 2 1.0 + j0.0 0.2 0.0 0.0 0.0 3 1.0 + j0.0 0 0 0.6 0.25
Tam responsible for any violations with regard to this. A load of 135 MW at a power factor of 0.65 lagging can be delivered by a 3-phase transmission line. The voltage at the receiving end is to be maintained at 54 kV and the loss in the of transmission is 6 % of the power delivered. (Consider the line to be a short transmission line) Find ion Single phase Power delivered Per phase voltage snt flei
What are the basics of transmission lines? What is characteristic impedance? How can we derive the equation for characteristic impedance and velocity explain where got all symbols from? What is crosstalk and how do you calculate this? How is impedance measured?
The Power transfer capability of transmission line is most affected by: it) shunt conductance b) capacitance c) Resistance. d) inductance
A Three phase transposed line is composed of one conductor per phase with flat horizontal spacing of D as shown in the below figure. If GMD is 15.119 meters, then D will be a b D 2D Select one: Oa 12 meters Ob. None of these Oc15367 meters Od 14 meters