By using Gauss-Siedal method, the voltage of the bus 2 after two iteration is Your answer By using Gauss-Siedal method the voltage of the bus 3 after two iteration is Your answer For a system consist from 3 buses and bus 1 is the slack bus. The data of the system are:- 0.25 -0.2 -0.05 Ybus =j-0.2 0.225 -0.025 p.u. -0.05 -0.025 0.075 V₁=1+j0 p.u., P₂+jQ2-0.6+j0.25 p.u., P3+jQ=0.8+j0.5 p.u.

By using Gauss-Siedal method, the voltage of the bus 2 after two iteration is Your answer By using Gauss-Siedal method the voltage of the bus 3 after two iteration is Your answer For a system consist from 3 buses and bus 1 is the slack bus. The data of the system are:- 0.25 -0.2 -0.05 Ybus =j-0.2 0.225 -0.025 p.u. -0.05 -0.025 0.075 V₁=1+j0 p.u., P₂+jQ2-0.6+j0.25 p.u., P3+jQ=0.8+j0.5 p.u.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Discuss the advantages and limitations of Gauss-Seidal and Newton Raphson methods . Of this two, which method is generally preferred for solving the load flow problems?
A DC Optimal Power Flow problem is to be solved for a 3-bus network. The per-unit reactances of the lines interconnecting the buses are as follows: X12 = 0.1pu, X13 = 0.12 pu and X23 = 0.2 pu. There is a generator at each bus. The loads at buses 1, 2 and 3 are 150MW, 200mw, and 100MWrespectively. Bus 1 is taken as the reference bus, and SBase = 100 MVA. Which one of the below is a constraint of the DCOPF problem? Select one: O a. None of these O b. -500 0₂-1000 03 = P3 - 110 O c. 1500 0₂-500 03 = P₂ - 220 O d. 1500 0₂-500 03 = P₂ - 200 O e. -500 0₂-1000 03 = P3 - 150 O f. -1500 8₁-1000 03 = P₁ - 150
Determine the best-fit line equation of the curve. (Note the constants and their units.) (The picture is the basis for this)
Following figure shows the one-line diagram of a two bus system. Take bus 1 as slack bus, bus 2 as load (PQ) bus. Neglect the shunt charging admittance. Obtain the bus admittance matrixYBUs and find V₂ and 62, power flows and line losses using FDLF method. All the values are given in per unit on 100MVA base. Use a tolerance of 0.001 for power mismatch. 1 Z12= 0.12+10.16 Slack bus V₁ 1.0/0⁰ pu 2 PL2=1.0pu Q12=0.5pu
The figure below shows the one-line diagram of a four- bus power system. The voltages, the scheduled real power and reactive powers, and the reactances of transmission lines are marked at this one line diagram (The voltages and reactances are in PU referred to 100 MW base. The active power P2 in MW is the last three digits (from right) of your registration number (i.e for the student that has a registration number 202112396, P2 =396). [10] Starting from an estimated voltage at bus 2, bus 3, and bus 4 equals V2 (0) = 1.15<0°, V3 = 1.15 < 0°, V4 1.1< 0°. 1- Specify the type of each bus and known & unknown quantities at each bus. 2- Find the elements of the second row of the admittance matrix (i.e. [Y21 Y22 Y23 Y24]). 3- Using Gauss-Siedal fınd the voltage at bus 2 after the first iteration. 4- Using Newton-Raphson, calculate: |- The value of real power (P2), at bus 2 after the first iteration. Il- The second element in the first row of the Jacobian matrix after the first iteration. 2 P2…
Gauss-Elimination Solve the following systems of equations by using the Gaussian Elimination method.
In the following network, the voltage magnitudes at all buses are equal to 1 p.u., the voltage phase angles are very small, and the line resistances are negligible. All the line reactances are equal to j1 p.u. (1) (2. P₂ = 0.1 p.u. P3 = 0.2 p.u. The voltage phase angle 83 in radian at bus 3 is (Assume one of the generator bus as slack bus and sin-¹ (0.1) = 0.1 rad) (a) -0.1 (b) -0.2 (c) 0.1 (d) 0
One of the following load flow analysis method is found to be more efficient for large power systems. Gauss- Jordan Method Gauss- Seidal Method Newton- Raphson Method Gauss Method
How do we handle a PV bus in the Gauss Seidel Method? What will happen to the bus voltage if the reactive power at a PV bus exceeds the upper bound? And why?
A network consisting of a set of generator and load buses is to be modeled with a DC power flow, for the sake of conducting a contingency analysis. The initial flows calculated with the DC power flow give the following information: f°2-4 = - 65.3 MW and fº4-5 = 13.6 MW. The following values of LODF and PTDF factors are given: PTDF54,2-4 = -0.2609, LODF2-4,4-5 = -0.6087. Calculate the contingency flow on line 2-4 due to outage of line 4-5. Select one: O a. -75.5MW O b. None of these O c. -68.85MW O d. -73.58MW O e. 75.5MW O f. -61.75MW
One of the following load flow analysis method is not more efficient for large power systems. Gauss- Jordan Method Gauss Method Gauss- Seidal Method Newton- Raphson Method
Solve numerical : Following figure shows the one-line diagram of a two bus system. Take bus 1 as slack bus, bus 2 as load (PQ) bus. Neglect the shunt charging admittance. Obtain the bus admittance matrixYBUS and find V2 and δ2, power flows and line losses by using Fast decoupled power flow method. All the values are given in per unit on 100MVA base. Use a tolerance of 0.001 for power mismatch.