12 e12 R8 R4 -X cs 13 e13 Figure 2140

Q: Thevenin and Norton Equivalent: 15). For the circuit in Fig. 4.109, find Thevenin equivalent between…

A: We need to find out thevenin equivalent circuit and norton equivalent circuit

Q: List the minimum trade size Type EMT for each of the following applications. (Objective 12-1)…

A: As per Bartleby expert policy only first individual question is to be answered. So, answering only…

Q: do you have any other method to solve this problem??

A: In the given circuit,we need to find above mentioned parameters.

Q: Grateful help with Part B please.  Thanks

A: Characteristic impedance is a property of the material that determines whether or not it can…

Q: How many nodes are there? image d.png ... 1.5 0 20 50 2 A( )5 A Answer _nodes

A:

Q: What information is contained in the specification K, 10,000

A: Kp stands for the position error constant for the step input function.  here, Kp = 10000

Q: Vab=C --- ) v (a) 2.5 v (b) - 2.5 v (c) - 10 v (d) 10 V

A: The solution can be achieved as follows.

Q: I dont get it. howcan I make sure its in low condition?

A: You have asked that how to make sure it is in low condition.

Q: hat is the approximate voltage amplitude and frequency of the waveform below?

A: Disclaimer: "Since you have asked multiple questions, we will solve the first question for you. If…

Q: Find % Regulation for the given readings VR(Line to Line ) = 394 Volts, Vs(Line to Line ) = 458 %3D…

A:

Q: Telecom operator has been assigned the bandwidth from 2100MHZ to 2105MHz, this can support 100 voice…

A: Given data: The bandwidth from 2100 MHZ to 2105 MHz. There is a guard band of 10 KHz

Q: please tell me last part answer

A: let Z = a+jb  then a is called real part and b is called imaginary part .

Q: Please answer in typing format

A: The Peltier effect is the result when electric current is passed between two materials,such that it…

Q: TOPIC: Power Systems, Power Plants & Illumination INSTRUCTIONS: - Answer in this format: Given,…

A: Given information is written below. The room dimension is l×w×h=20 m×10 m×5 m. Lamp is placed at the…

Q: Which of the following do not apply to a primitive network? (a) It has two terminals. (b) It is…

A: The power system has to transmit power from the generation side to the load side. For this purpose,…

Q: The balanced system below has a phase voltage of 120 V. It supplies a balanced load coil that is…

A:

Q: Find the difference. 11010011two − 1011101two _____two

A: We will first convert the given binary numbers into decimal. The subtraction of these decimal…

Q: What can you do in the sim

A: You can do several things in the sim is as follows;  1.You can recreate yourself and friends in the…

Q: In the circuit below I = 3245° mA. What is the KCL expression at node a following the %3D…

A:

Q: For measurement instrument, the crucial -1 static characteristic is resolution аccuracy sensitivity

A: Since there are multiple questions uploaded within the same question, therefore solving the first…

Q: 4. What are the roles of speakers and amplifiers in the cellphones?

A: We are authorized to answer only 1 question at a time since you have not mentioned which question…

Q: L{7te¬5t cosh(3t) + +sin(Võt) – rº + e%}

A:

Q: What are the Rules in Performing Laboratory experiments in the Electrical Engineering Laboratory?…

A: It's vitally important to take safety precautions when working with electricity. Safety must not be…

Q: 12 M R1 120 VAC 13.2 H L1 1k2 MW R2 60 Hz

A:

Q: Determine Reg in Ohms at the (a,b) terminals for the following circuit. Round your answer to the…

A:

Q: 13-Find the Thevenin and Norton equivalent circuits between ab. 2 A a 6 0 18 V 3 A 10 V

A: Given:

Q: 200 200 20 0.53

A:

Q: Explain the benefits of using analogue and digital electronic devices/systems, using the following…

A: Telephones:Analog: Analog telephone systems transmit voice signals as continuous electrical signals.…

Q: Look at the photo and answer the questions

A:

Q: Okumura model is applicable for distances of

A: The solution is provided in the following section:

Q: Can you please further explain this section.

A:

Q: if i use Voltage division instead of nodal analysis. where do you suggest i start, and How do I…

A:

Q: 5. Determine whetneo or not each of the following systems are i) yon) = >cCn) + n.xcn+1) (i) yen) =…

A: A system is BIBO-stable only if bounded-input always produces bounded output.

Q: Fill the following blanks in the sub-program with suitable numbers to generate 7 sec delay.

A: Explanation:The outer loop (D2) is initialized with a count of 7 to achieve a 7-second delay.The…

Q: please tell me a similar app to solve engineering questions?

A: Bartleby is the best app Bartleby is the best app

Q: Vdc0 U=12 V Circuit #1 Ried LED www Ried_series Vdc0 U= 12 V Current in LED (A) Circuit 0.03 #₂ 0.02…

A: Given Data:An LED illumination circuit with,Supply voltage Set-current of the diodes V-I…

Q: What Is a function of a capacity

A:

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.