In the power system network shown in Figurebelowbus 1 is a slack bus with 1.0/0° per unit and bus 2 is a load bus with S2 = 300 MW + 80 Vi %3D %3D Mvar. The line impedance on a base of 100 MVA is Z = 0.01 + j0.02 per %3D unit. (a) Using Gauss-Seidel method, determine V. Use an initial estimate of V = 1.0 + j0.0 and perform two iterations. i.e.Deternine (a)V2' and (b)Vz? Z12 = 0.01+ j0.0 2 || 2 S 300 MW+j80 Mvar (a) 0.945 - j 0.025 (b) 0.994- j0.0571 (a) 0.965 - j 0.0255 (b) 0.914 - j0.0529 (a) 0.954 - j 0.052 (b) 0.949 - j0.0517 (a) 0.914 - j0.0152 (b) 0.949 - j0.0517

In the power system network shown in Figurebelowbus 1 is a slack bus with 1.0/0° per unit and bus 2 is a load bus with S2 = 300 MW + 80 Vi %3D %3D Mvar. The line impedance on a base of 100 MVA is Z = 0.01 + j0.02 per %3D unit. (a) Using Gauss-Seidel method, determine V. Use an initial estimate of V = 1.0 + j0.0 and perform two iterations. i.e.Deternine (a)V2' and (b)Vz? Z12 = 0.01+ j0.0 2 || 2 S 300 MW+j80 Mvar (a) 0.945 - j 0.025 (b) 0.994- j0.0571 (a) 0.965 - j 0.0255 (b) 0.914 - j0.0529 (a) 0.954 - j 0.052 (b) 0.949 - j0.0517 (a) 0.914 - j0.0152 (b) 0.949 - j0.0517

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1- define A. Microgrid B. Distributed generation C. Discuss the advantages and disadvantages of microgrid systems over conventional power systems
Explain the concept of distributed generation and its potential impact on traditional power systems.
QUESTION 3 а) Describe a static energy component in power electronics fundamental. A single-phase full-wave ac voltage controller working on the ON-OFF control technique b) has a supply voltage of 230 V (RMS) 50 Hz with a purely resistive load that is connected in series as of 35 N and 10 Q. The controller is set to ON-mode for 40 cycles and off for 20 cycles. i) Justify whether the converter is operating at the optimum duty cycle (k) of> 50%. ii) Analyse the capability of the converter in supplying the load at 180 V (RMS).
PLEASE EXPLAIN STEP BY STEP/SIMULINK Consider the following article by X. Wang, J. Yong, W. Xu and W. Freitas, "Practical Power Quality Charts for Motor Starting Assessment.This article carries out a study of how the starting of triphasic induction motors affects the power quality of a circuit.
Q6) A three-phase to single-phase, three-pulse cycloconverter delivers power to a load rated at 100 V, 30 A, 25 Hz with power factor 0.8 lagging. a) Draw & derive the output voltage if the ap-60° b) Estimate the necessary input voltage and power factor. c) Draw the mean output voltage if the input frequency is 200Hz. M
A three-phase, fully-controlled thyristor bridge converter is used as line commutated inverter to feed 50 kW power at 420 V dc to a three-phase, 415V (line), 50 Hz ac mains. Consider de link current to be constant. The RMS Current of the thyristor is (a) 119.05 A (b) 79.37 A (c) 68.73 A (d) 39.68 A
A.C. distribution calculationg differ from of d.c. distribation power factor, vectorially calculations, load O power factor only O load only,
Discuss the Power transmission from home to powerplants and provide a picture
Don't copy from Chegg and other websites. Please explain in detail.