The 13.2 kV 50-Hz generator feeds a load over a line with (Zload) impedance Zline. Load is 80on + j500N and impedance of the line is 20 + j300 a) If the generator is directly connected to the load as given in (a), what will be the line losses? b) If the generator is connected to the load using step-up and step-down transformers as given in (b), what will be the line losses? c) How much is the increase in efficiency compared to (a) from (b)? Zline (a) 1:10 10:1 Zline Tr1 Tr2 (b) Zload Zload

The 13.2 kV 50-Hz generator feeds a load over a line with (Zload) impedance Zline. Load is 80on + j500N and impedance of the line is 20 + j300 a) If the generator is directly connected to the load as given in (a), what will be the line losses? b) If the generator is connected to the load using step-up and step-down transformers as given in (b), what will be the line losses? c) How much is the increase in efficiency compared to (a) from (b)? Zline (a) 1:10 10:1 Zline Tr1 Tr2 (b) Zload Zload

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1 Two transformers A and B are connected in parallel to a load of (2+j1.5)2. Their impedances in secondary terms are ZA = (0.15 + j0.5)2 and ZB= (0.1 +j 0.6)2. Their no-load terminal voltage are EA 207 /0° volt and EB = 205/0° volt. Find the power output and power factor of each transformer.
When this generator is connected to a 13.8 kV distribution feeder of negligible impedanceand operates at an output power of 8.75 MW at 0.9 power factor lagging, work out the field current, the reactive-power output, and the load angle for this operating condition.
If the line-to-line primary voltage and line current is 1.0 at 0 degrees, what is the secondary line- to-line voltage for the following three-phase transformers? Assume a turns ratio of N = 10. Express answer in polar form. a. Delta-to-Delta: b. Delta-to-Wye: c. Wye-to-Delta: d. Wye-to-Wye:
A synchronous generator is rated 645 MVA, 24 kV, 0.9 pf lagging. It has a synchronous reactance 1.2 . The generator is feeding full load at 0.9 pf lagging at rated voltage. Calculate: (a) Excitation emf (E,) and power angle 8 (b) Reactive power drawn by the load Carry out calculations in pu form and convert the result to actual values.
There is a three-phase system such that the phase current in the generator, lines and charging phase is the same. The phase voltage in the generator must be 1000 [V] with clockwise sequence. The connected load must be such that the phase current in each load is 10 [A] and its power factor is 0.97 “lagging”. a) Determine phase currents in the generator, lines and phase in the load
A synchronous generator runs at 250 rpm and generates at 50-Hz. There are 216slots, each containing 5 conductors arranged in a full-pitched winding for 3-phasestar connection. All the conductors of each phase are in series and the flux perpole at no-load sinusoidally distributed over the pole pitch is 30 mWb. Find the emfinduced in each phase winding and the terminal voltage.
9.09 The flux density distribution in the air-gap of a certain generator is such that it contains a fundamental, a third harmonic, and a fifth harmonic. The flux per pole due to the fundamental distribution is 9 x 10-3 weber, that due to the third harmonic distribution is 0.9 x 10-3 weber, that due to the fifth harmonic distribution is 0.4 x 103 weber. There are four armature slots per phase per pole, the connection are made for three-phase wye. and the coil pitch is 12/15. The frequency is 60 cycles and the generator has 4 poles. (a) Calculate the emf/turn. (b) If there are six turns/coil and two coil sides/slot, calculate the emf per phase. (c) Calculate the emf between line terminals. Ans. 2.32V; 212V; 364V
A 10 MVA three phase load is to be served by a three phase transformer at aline voltage of 13.8 kV. The supply side voltage(line-line) is 138 kV. Varioussingle phase transformers are available in the warehouse but all havewindings with voltage ratings under 100 kV and current ratings under 250 A.Is it possible to serve the load using only three single phase transformers? Ifso, specify the three phase connections and the low and high voltage ratingsof the single phase transformers.
If the load draws a current of 2727 A, in phase, from a generator, which of the following statement is true? O A. The reactive power is flowing from generator to the load and the real power is flowing from the load to the generator. O B. Since the current is in phase with the generator voltage, both the real and reactive power is flowing from the generator to the load. O .Since the current is leading the generator, both the real and reactive power is flowing from the load to the generator. O D. The real power is flowing from generator to the load and the reactive power is flowing from the load to the generator. O E. None of the other choices are correct
L-type equivalent circuit and parameters for a continuous sinusoidal phase of a 5.5 kW, 1460 rpm, line voltage 220 V and frequency 50 Hz star-connected 3-phase ASM, ignoring core (iron) losses given as follows: R1=0.21 Ohm, R2=0.18 Ohm, X1=X2=0.66 Ohm and Xm=9.9 Ohm How many times the inrush current will be the rated current when the ASM is started directly? Answer options group 3.7473 5.2280 8.0815 7.1534 1.2558 4.3763 2.6455 6.3414
In the system shown in Figure 1, the transformers are connected star-star with both star points grounded and the generator is connected in star with its star points grounded. The per unit impedances of each element on a 40 MVA base are given in Table 1 and the voltage levels are given in Table 2. Z [p.u.] 0 2 tööt Generator 0.01 +j0.08 p.u. L Figure 1: A section of the distribution system Transformer T1 Line V BASE [KV] 0.04 + j 0.03 + j 0.15000000000000002 0.06000000000000000 Generator Table 1: Sequence impedances (p.u. on 40 MVA base) 3 T2 181. Line 3 10 Table 2: Voltage bases (kV) Load 1 Transformer T2 Load Current A load current of 11.316 kA is flowing with a lagging power factor of 90 %. Convert this to a current vector in per-unit. IL = 0.04 + j 0.06000000000000000