1Two transformers A and B are connected in parallel to a load of (2+j1.5)2. Their impedances insecondary terms are ZA = (0.15 + j0.5)2 and ZB= (0.1 +j 0.6)2. Their no-load terminal voltageare EA 207 /0° volt and EB = 205/0° volt. Find the power output and power factor of eachtransformer.

Answered: Image /qna-images/answer/cfcc0487-32f8-49e0-9e68-f9fffe4fedf6.jpg

Two transformers A and B are connected in parallel to a load of (2+j1.5). Their impedances in secondary terms are ZA = (0.15 + j0.5)2 and Z8 = (0.1 +j 0.6)2. Their no-load terminal voltage are EA 207 20° volt and EB 205/0° volt. Find the power output and power factor of each transformer.

Two transformers A and B are connected in parallel to a load of (2+j1.5). Their impedances in secondary terms are ZA = (0.15 + j0.5)2 and Z8 = (0.1 +j 0.6)2. Their no-load terminal voltage are EA 207 20° volt and EB 205/0° volt. Find the power output and power factor of each transformer.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Find the following : 1.Ripple Voltage (vpp) 2. Zero-to peak ripple(Vop) 3.secondary winding of the transformer high line and low line
Two single-phase transformers whose phase electrical equivalent circuits are given below are connected in parallel and ZL= 0.8+j0.6ohm is feeding a worth of load. Idle operating voltage of Transformer 1 is 220 V and Transformer 2 idle operating voltage is 240V.a.) Find the currents flowing from transformers to the load.b.) Find the active powers that transformers transfer to the load.
Consider the three single-phase two-winding transformers shown in Figure. 3. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in A, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a', b', and c' such that VAN is 90° out of phase with V₂'b' for positive sequence. DI H₂ Figure. 3: Three-Winding Transformer
A short transmission line connects a step-up transformer on the source side with a series impedance of j0.5 ohms (referred to the primary) to a step-down transformer on the load side with a series impedance of 50 ohms (referred to the primary). The turn ratio of the step-up transformer is 1:14 and a no-load primary voltage of 17 (line-to-line) kV. The step- down transformer has a turn ratio of 18:1 and it has a Y-connected, balanced load of 0.463 +j 0.0772 ohms connected to its secondary side. A capacitor bank of -j0.324 ohms is added parallel to the load. Assuming an ideal transmission line, the effective impedance (per phase) of the system seen by the source would be: O A. 0.292 + j0.375 O B. None of the other choices are correct O C. 0.584 + j0.750 O D.0.196 + j0.158 O E. 5.84 + j7.5
3. A non-ideal 1-phase transformer has turns ratio 5:1 with 120Vac primary. The primary impedance is 1 + j1 Ohms, and the secondary impedance is 0.2 + j0.2 Ohms. Assume the core impedance (R0 and X0) can be neglected. A resistive load of 12 Ohms is connected to the secondary. What is the primary current magnitude? What is the secondary voltage magnitude? What is the efficiency of this transformer with this load?
In the transformer circuit below, a load of 2.5cis20° Ohms is connected to the output terminals of the transformer. If the voltage across the load is 230V, determine:a. Load current, I(L)b. Imc. Icd. Source voltage, V
please answer in short....please....i will like.
What is the role of transformers in power distribution, and how do they work to step up or step down voltage levels?
a single-phase transformer serves a 7.2kw resistive loadlocated 200 ft from the transformer. each conductor from the transformer to load has an impedence of (0.78+j0.052) ohms per 1000ft. if the voltage at the load terminal is 240v, the magnitude of the voltage (v) at the transformer secondary is most nearly:
8. The two winding transformer and the autotransformer of the circuit shown in Figure are ideal. Determine the conducting and transformed currents of auto transformer. N1=200 NBC=20 N2=100 NBA=30 10A B 200 V 50,Hz C N1: N2
1. A 10 kVA, single-phase, 2400-V:120-V, 60 Hz transformer has an equivalent impedance referred to LV side of 0.01 + j0.09 Q. This transformer has a core loss of 100 W at rated voltage. When rated current is applied to the 2400-V winding, the exciting current in that winding is found to be 0.2 A. a. Find the full-load regulation of this transformer at a power factor of 0.8 lagging. b. Find the efficiency of this transformer at full load, 0.8 power factor lagging. c. Ifstandard open-circuit and tests were performed on this transformer, what would be the measured values of these tests?
6.5% ans ex A so kvA. 2o00/20 V, So He single-phase transformar has impedance drof of8% and resistance drop of 4%. Caleulate. The Requlation of the Thams former at full- Load o8 P.s Legging. also find The Power factor at which Voltage requlation will Be Zero. Sols 0.5 leading. s alculate The % Noltege Requlation af atransformar in w hich the Percantage resistance drof is 1% and Percentage dre is 6% when The Power fador is 0.8 lagging ) > unity aMS 38 % ans 1 % (シ→ 0.8 leading . amS - 2.2%