PER-UNIT SYSTEM TUTORIALTutorial 3Draw an impedance diagram for the electric power system shown in Figure 3showing all impedances in per unit on a 100-MVA base. Choose 20 kV as thevoltage base for generator. The three-phase power and line-line ratings aregiven below.X = 9%X = 16%X = 20%X = 9%X = 120 QS = 48MW + j64MVarG1:90MVA20kVT1:80MVA20/200kVT2:80MVA200/20kVG2:90MVA18kVLine:200kVLoad:200kV PER-UNIT SYSTEM TUTORIALTutorial 3Answer:j0.2j0.3 j0.25j0.1j0.0810.75 + j1.0(G1G2Figure 3 – Per-unit impedance diagram for Tutorial 3

The equivalent circuit of a power system is the impedance diagram, in which the various components…

Draw an impedance diagram for the electric power system shown in Figure 3 showing all impedances in per unit on a 100-MVA base. Choose 20 kV as the voltage base for generator. The three-phase power and line-line ratings are given below.

Draw an impedance diagram for the electric power system shown in Figure 3 showing all impedances in per unit on a 100-MVA base. Choose 20 kV as the voltage base for generator. The three-phase power and line-line ratings are given below.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

3.8. Three identical 9-MVA, 7.2-kV/4.16-kV, single-phase transformers are con- nected in wye on the high-voltage side and delta on the low voltage side. The equivalent series impedance of each transformer referred to the high-voltage side is 0.12 + j0.82 S per phase. The transformer supplies a balanced three- phase load of 18 MVA, 0.8 power factor lagging at 4.16 kV. Determine the line-to-line voltage at the high-voltage terminals of the transformer.
2.5.3 A three phase power system has two generator connected in parallel to a transformer and subsequently to a 230 kV transmission line. The ratings for the components are given as below: Generator 1:10 MVA, reactance of 12%. Generator 2: 5 MVA, reactance of 8%. Transformer: 15 MVA, reactance of 6% Transmission line: impedance of 4+j60 2, for which the reactances in percentage are based on the ratings of the respective components. Obtain the reactance and impedance values of the components in the system in percentage, based on 15 MVA and rated voltage of the components.
A 4-bus three-phase power system consists of the following equipment: • Generator 1 connected to bus 1 with a rated power of 20MVA, rated voltage of 20 kV, and a series reactance of 0.4 p.u. • Generator 2 connected to bus 5, with a rated power of 12MVA, rated voltage of 10 kV, and a series reactance of 0.3 p.u. Transformer 1 connected between buses 1 and 2, is wye-wye connected with a rated power of 20 MVA, rated voltages 20/100 kV, and a series reactance of 0.1 p.u. • Transformer 2 connected between buses 4 and 5, is wye-wye connected with a rated power of 12 MVA, rated voltages 12/110 kV, and a series reactance of 0.15 p.u. • Transmission Line 2-3 connects buses 2 and 3 and had a series impedance of 50 + j75 ohms. • Transmission Line 3-4 connects buses 3 and 4 and had a series impedance of 40 + j80 ohms. • Load A connected to bus 3 and abosorbes20 MW and 10 MVAR. The voltage at bus 3 is 105 kV. 1) Draw the one-line diagram for the system. 2) Draw the per-unit, per phase…
There is a three-phase system such that the phase current in the generator, lines and charging phase is the same. The phase voltage in the generator must be 1000 [V] with clockwise sequence. The connected load must be such that the phase current in each load is 10 [A] and its power factor is 0.97 “lagging”. a) Determine phase currents in the generator, lines and phase in the load
Question 3. A three-phase impedance load balanced D a connected load in parallel with a balanced ? connected load made of bonding. D each arm for the load ?D = 6 + 6? and ? each arm for the connected load It is given as ?? = 2 + 2?. ? the connected load ?? = 1? is earthed through the neutral impedance. To this impedance load, the symmetrical component voltages ?0 = 10∠60°, ?1 = 100∠0° and ?2 = Unbalanced phase-to-earth voltages ??, ?? and ?? of 15∠200° volts were applied. a) Draw the zero, positive and negative sequence circuits. b) Find the complex powers imparted to each component circuit.
2.2. The figure below shows a radial transmission system with a generator having a per-unit voltage of 1.3 at an angle of 9 degree p.u. The load demand is 47MW at a power factor of 0.96lagging. Use the nameplate values of Transformer 2 as base values and calculate the following: Correct answers to three decimal places : 25..Per unit impedance of transformer and it's angle 26.Per unit voltage of the line and its angle 27.Per unit impedance of the line and its angle. And Reactance of the transmission line when the load consumes full-load (Ω).
The figure below shows the one-line diagram of a four- bus power system. The voltages, the scheduled real power and reactive powers, and the reactances of transmission lines are marked at this one line diagram (The voltages and reactances are in PU referred to 100 MW base. The active power P2 in MW is the last three digits (from right) of your registration number (i.e for the student that has a registration number 202112396, P2 =396). [10] Starting from an estimated voltage at bus 2, bus 3, and bus 4 equals V2 (0) = 1.15<0°, V3 = 1.15 < 0°, V4 1.1< 0°. 1- Specify the type of each bus and known & unknown quantities at each bus. 2- Find the elements of the second row of the admittance matrix (i.e. [Y21 Y22 Y23 Y24]). 3- Using Gauss-Siedal fınd the voltage at bus 2 after the first iteration. 4- Using Newton-Raphson, calculate: |- The value of real power (P2), at bus 2 after the first iteration. Il- The second element in the first row of the Jacobian matrix after the first iteration. 2 P2…
Is it true??
What is the alternators terminal phase voltage at shorted load condition? Explainand justify your answer in one(1) sentence.Use IA as the reference phasor.
10. A three-phase transformer consists of a bank of single-phase transformers connected to form a Dd0 connection. A fault on one of the transformers causes it to be removed from the circuit, and the remaining two transformers are connected in an open-delta (V-V) connection. Show that the capacity of the open-delta connected transformers is 58% of the delta-connected transformers.
Connect the wires into a OPEN DELTA configuration .