Q4. Figure Q4. shows a power system with one generator, two transformers, a lineand a load.Zload=0.3+j0.102GVgen-415/0°VR = 0.02 2totZLine=1+j0.10600 kVA0.415/11 kV Y-YXT1=6%tot500 kVA11/0.415 kV Y-YXT2=5%Figure Q4. A Simple Power System b) What are the main advantages and disadvantages of using per-unitanalysis?c) If a 4 p.u lightning induced overvoltage strikes the line section of thesystem shown in Figure Q4, calculate the actual overvoltage in thegenerator, line and load sections (assuming no attenuation of the lightningtransient).

Part (c): Calculating Overvoltage Due to Lightning StrikeGiven Data:A 4 p.u. overvoltage occurs in…

Answered: Q4. Figure Q4. shows a power system…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.8MCQ: An ac resistance is higher than a dc resistance. True False

See similar textbooks

Similar questions

The principle operation of LVDT is based on the variation of Select one a. Self inductance b. Reluctance c. Mutual inductance d. Permanence
Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in , place the polarity marks, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a, b, and c such that VAN is 90 out of phase with Va for positive sequence.
Match the following: (i) Hysteresis loss (a) Can be redud by constructing the core with laminated sheets of alloy steel (ii) Eddy current loss (b) Can be reduced by the use of special high grades of alloy stl as core material.
Determine the peak-to-peak ripple and dc output voltages in Figure 2. The transformer has a 48 V rms secondary voltage rating, and the line voltage has a frequency of 60 Hz. (you may neglect Rsurge). 120 V rms 00000 ellee Figure 2 Rug www 10 100 F ww R₁ 3.3k
Explain step by step please a b and c
Two 300-VA parallel-connected transformers can supply a maximum load of a. 150 VA b. 300 VA c. 450 VA d. 600 VA
Determine the current I2 for the transformer in Figure if the flux in the core is 1.5x10³ Wb. 1₁ (2A) N₁ = 60 turns 1₁ 20 1.8 1.6 1.4 1.2 1.0 0.8 0.6 +B(T) 0.4 0.2 300 600 Sheet steel .d Area (throughout) = 0.15 x 10³ m² labeda = 0.16 m 900 1200 1500 1800 2100 2400 Cast iron 2700 3000 3300 Sheet steel Cast steel N₂ 12 = 30 turns 4200 4500 H(Alm)
6. For the air core transformer circuit shown below, determine the currents la and lb in the direction shown. Express each answer in polar form. R1-302 www la ZI1=150 E=10/0 M=j20 Ze= n Z12=j62 lb R2=50 la Ib
Functions/Interface/acellus_engine.html?ClassID=500072518 Two step-up transformers are connected in series, the secondary of the first to the primary of the second. Both transformers have the same turns ratio, and are identical. If the input voltage is 12.0 V AC and the output voltage is 300 V AC, what is the voltage, Vint, in between the two transformers? Vint = [?] V St Voltage (V) 023 International Academy of Science. All Rights Reserved. DELL Enter 68°F C
helpp
Determine the currents IR1 and IR2, (show as positive values – actual current direction). Verify in Multisim using measurement probes or digital multimeter
Give two reasons why transformers are an important part of the power distribution grid

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning