Q130: If the value of maximum shear stress for the pins at A, B and C is 90 MPa, and the diameter of pins at A, B and C is 15 mm subjected to double shear. Also, if the maximum normal stress of the bar BC is 120 MPa and its diameter is 35 mm. Determine the maximum safe value of the distributed load (w).

Q130: If the value of maximum shear stress for the pins at A, B and C is 90 MPa, and the diameter of pins at A, B and C is 15 mm subjected to double shear. Also, if the maximum normal stress of the bar BC is 120 MPa and its diameter is 35 mm. Determine the maximum safe value of the distributed load (w).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Situation 1: A flexible cable and rigid boom system is used to lift a load of 65kN at the end of…

Q: A W section is used as a column of hinged ends with a length of 6 m. Fy = 248 MPa and E = 200GPa.Use…

Q: 4.Steel strips , stretched with a force of F = 4,8kN, are fastened with 3 bolts. Materials steel…

Q: The pins at C and A are in double shear, and the pin at B is in single shear. All pins have a…

Q: Q2// The control arm is subjected to the loading shown in Fig.2. Determine the required diameter of…

Q: H.W 1 The bracket plate is 40 mm thick. b= 272 mm. Load on the bracket, P= 100 kN; spacing, C (…

A: 1. Draw a diagram for the given cross-section. Here, A, B, C, D, E, F indicate the shown rivets, Fp…

Q: The ultimate stress for a hollow steel column which carries an axial load of 1.9MN is 480N/mm if the…

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of…

Q: The boom AC is a 4-in. square steel tube with a wall thickness of 0.25 in. The boom is supported by…

Q: The yoke-and-rod connection is subjected to a tensile force of 135 kN. The material of pin A has a…

Q: A W section is used as a column of hinged ends with a length of 6 m. Fy = 248 MPa and E = 200GPa.Use…

Q: 1800 mm apart and the central band is 89 mm wide. The central load is to be 3.5 kN w nissible stress…

Q: Two # 10-24 screws are used to mount the hook in the ceiling as shown. The screws are tightened so…

A: Given : Number of screws (n) =2 Size of the screws : #10 - 24 , which means d=316in and Thread…

Q: The solid steel rod (1) has an allowable shear stress of 17 ksi. The brass tube (2) has an allowable…

A: given; allowable shear stress for rod (τ)=17ksi…

Q: متبقي ۰۲:۲۶:۱۸ Four forces F1, F2,

A: Given Data⇒ F1=10 NF3=10 NF2=4 NF4=14 N

Q: n the steel structure shown in the figure, a 6 mm diameter in is used at C and 10 mm diameter pins…

Q: An axial load of 5000 kN is to be supported by short reinforced concrete column 400 mm x 500 mm with…

A: Given: The axial load, P = 5000 kN The area of the column, Ac = 400 mm x 500 mm The length of the…

Q: The one end of a hollow square bar whose side is (10+N/100) in with (1+N/100) in thickness is under…

Q: Q2: A composite bar is made up two vertical rods of steel and copper each of length 2 m and diameter…

A: from the above figure given data is load is 15KN in the given question find out each load on the…

Q: The solid steel rod (1) has an allowable shear stress of 13 ksi. The brass tube (2) has an allowable…

A: The largest torque that can be applied safely at the upper end of the steel rod: Tmax = 319.07 lb•in

Q: 210. An aluminum tube is fastened between a steel rod and a bronze rod as shown in Fig. P-210. Axial…

Q: Use the graphical method to construct the shear-force diagram and identify the magnitude of the…

Q: The minimum factor of safety i able load P that may be applied

A: A=1.25in2yield strengthSyt = 46ksidiameterd=0.3inUltimate shear strengthSus=76ksiFOS=1.8a=53in…

Q: If load P = 20.3 kips, determine the normal force in bar (1). D A 6 ft 43.8 kips 31.0 kips 33.8 kips…

Q: Determine the maximum safe load P that can be applied to the machine part that is 90-mm wide and…

A: GivenW=90mmt=12mmσallow=100Mpa

Q: Two 8-in-wide wooden boards are to be joined by splice plates that will be fully glued onto the…

A: Data given- P = 20000 lb a = 0.4 in Shear strength = 145 psi w = 8 in

Q: y, determine the required diameter of the rod.

Q: Part A Determine the smallest diameter of the rod that will support the load ofP = 3.4 kip without…

Q: The five-bolt connection shown must support an applied load of P-500 kN. If the average shear stress…

Q: Q120: Determine the stress in cable shown in the figure if its diameter is 10mm. If the pins at A…

A: Consider the free body diagram as shown below for the given system.

Q: As part of a processing of biofuels, water is pumped into a circular tank with a diameter Dt, as…

A: For the solution refer below images.

Q: Grant Kiehl - Emch213 4. 1-93. The rods AB and CD are made of steel. Determine their smallest…

Concept explainers

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.

Question

20mm
Q130: If the value of maximum
shear stress for the pins at A, B
and C is 90 MPa, and the
diameter of pins at A, B and C is
15 mm subjected to double
shear. Also, if the maximum
normal stress of the bar BC is
120 MPa and its diameter is 35
mm. Determine the maximum
safe value of the distributed load
4 m
(w).

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Clutches, Brakes, Couplings and Flywheels

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q30: The pin B supports the Load W= 9000 lb and connects horizontal cable with point A. If the pin C is subjected to double shear while pin at B is a single shear. The diameter of pin C is 1.5 in while the diameter of pin B is 0.8 in. Determine the shear stress at pins B and C. Also find the stress in the cable AB if its diameter is 0.5 in. 6 ft W 9 ft
4
Q140: The diameter of pins at A and D is 10 mm subjected to 2m 2m double shear while the diameter of pin at C is 15mm subjected to single shear. Determine the shear stress in pins A,D and C and the stress in the bar DC diameter is 40 mm. 1.5 m 5 kN if its
' Three piates are joined with a 12-mm diameter pin as shown beiow. Determine the maximum load p that can be transmitted by the joint if the maximum bearing stress between a plate and the pin must be limited to 650 MPa .
Rigid bar ABC is supported by bronze rod (1) and aluminum rod (2), as shown. A concentrated load P is applied to the free end of aluminum rod (3). Bronze rod (1) has an elastic modulus of E₁ = 15,000 ksi and a diameter of d₁ = 0.40 in. Aluminum rod (2) has an elastic modulus of E₂ = 10,000 ksi and a diameter of d₂ = 0.70in. Aluminum rod (3) has a diameter of d3 = 1.00in. The yield strength of the bronze is 48 ksi and the yield strength of the aluminum is 40 ksi. Assume a = 2.5 ft, b = 1.5 ft, L₁= 6 ft, L₂= 8 ft, and L3 = 3 ft. (a) Determine the magnitude of load P that can safely be applied to the structure if a minimum factor of safety of 1.8 is required. (b) Determine the deflection of point D for the load determined in part (a). (c) The pin used at B has an ultimate shear strength of 57 ksi. If a factor of safety of 2.7 is required for this double shear pin connection, determine the minimum pin diameter that can be used at B. L₁ T A Bronze (1) B Aluminum (3) D Aluminum P b (2) L3 •…
Required information A 920-mm (4) strip of steel (E= 200 GPa) is bent into a full circle by two couples applied as shown. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. M' M mm Determine the maximum thickness t of the strip if the allowable stress of the steel is 420 MPa. The maximum thickness t of the strip is mm.
Question 1 double-shear pin connections at Band D. All pins are 7 mm in diameter. a = 750 mm, b = 350 mm, h= 550 mm, P= 725 N, and 8 = 55° Determine the shear stress in pin B. Answer in MPa rounded-off to 2 decimal places. (1) a b P
The copper bar is subjected to a uniform loading shown in Fig. 10–24. Ifit has a length a = 300 mm, width b = 50 mm, and thickness t = 20 mmbefore the load is applied, determine its new length, width, and thicknessafter application of the load. Take Ecu = 120 GPa, ncu = 0.34.
- once answered correctly will UPVOTE!!
Question 5 of 5 View Policies Current Attempt in Progress For the connection shown, determine the average shear stress in the 0.75-in.-diameter bolts if the load is P = 60 kips. O 27.2 ksi O 37.5 ksi O 25.8 ksi O 21.9 ksi O 35.3 ksi
- once answered correctly will UPVOTE!!
All the pins are in double shear, and they each have a diameter of 14 mm. The average shear stress in each pin CANNOT exceed 70 MPa. What is the max magnitude of P that the beam can support