Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 11 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 8 mm in diameter. Assume a = 530 mm, b = 265 mm, h = 380 mm, and 0= 65°. If the normal stress in tie rod (1) cannot exceed 190 MPa and the shear stress in pin B cannot exceed 100 MPa, determine the maximum load Pmax that can be supported by the structure. D (1) a B b h P

Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 11 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 8 mm in diameter. Assume a = 530 mm, b = 265 mm, h = 380 mm, and 0= 65°. If the normal stress in tie rod (1) cannot exceed 190 MPa and the shear stress in pin B cannot exceed 100 MPa, determine the maximum load Pmax that can be supported by the structure. D (1) a B b h P

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The solid rod with radius r=37 mm is subjected to the loading F;=120 kN, F2=38 kN, F3=29 kN. With dimensions a=210 mm and b=330 mm Determine the magnitude of the combined shear stress at point B, given the following: Section Properties: b A=4300.84 mm? |= 1471963 mm A J= 2943925 mm4 Qmax= 33769 mm? B. O 0.310 MPa O 0,007 MPa O 0,620 MPa O 6.615 MPa O 4.805 MPa O 40.147 MPa O 13.176 MPa
3 - A roof truss and the detail of the riveted connection at joint B. Using allowable stresses of t = 70 MPa and ob= 140 MPa, how many 19-mm-diameter rivets are required to fasten member BC to the gusset plate? Member BE? P = 175 kN 6 m 14 mm gusset plate 4 m 4 m E 4 m 4 m P/2 P/2 75 x 75 x 13 mm 75 x 75 x 6 mm Pac
Need asap answer
A simple pin-connected truss is loaded and supported as shown. The truss is constructed from three aluminum members, each having a cross-sectional area of A = 1480 mm2. Assume a = 1.3 m, b = 6.0 m, and c= 3.6 m. If P = 55 kN and Q = 75 kN, determine the normal stress in each member. P 0← L. Answers: OAB = i OBC= i JAC = i a B MPa (C) MPa (T) MPa (T)
The bell-crank mechanism is in equilibrium for an applied load of F1 = 12 kN applied at A. Assume a = 330mm, b = 140mm, c = 80mm, and e = 35°. Pin Bis in a double-shear connection and has a diameter of 32 mm. The bell crank has a thickness of 23 mm. Determine (a) the shear stress in pin B. (b) the bearing stress in the bell crank at B. Bell crank F, Support bracket В A a F Answers: Tpin B = i MPa i MPa
please answer quickly
For a given Data of the riveted joint shown in the figure: Given: Diameter of each rivet = 3/4 inch Maximum allowable shear stress of rivet = 96.53 MPa 3. Maximum allowable bearing stress of plate = 124.11 MPa %3D Yield Strength of the key = 45 MPa Ultimate Strength of the key = 128.5 MPa %3D Determine the maximum safe value of P that can be applied to both ends in Kips or Kilo pound. The figure below: 4 in P 7/8 in 7/8 in
4) The composite shaft consists of a solid brass segment (1) and a solid aluminum segment (2) that are connected at flange B and securely attached to rigid walls at A and C. Brass segment (1) has a diameter of 18 mm, a length of L₁ = 235 mm, and a shear modulus of 39 GPa. Aluminum segment (2) has a diameter of 24 mm, a length of L₂ = 165 mm, and a shear modulus of 28 GPa. If a concentrated torque of 270 Nm is applied to flange B, determine (a) the maximum shear stress magnitudes in segments (1) and (2). (b) the rotation angle of flange B relative to support A. N y A 235 mm (1) B 165 mm 270 N-m (2) C x
A steel torsion bar AB with diameter d = 34 mm, and ductile material of tensile yield strength Sy = 276 MPa is attached to a rigid arm at A, supported by a bearing at C, and fixed at B, as the picture shows. At the right end of the arm is mounted the wheel on which the vertical force P acts from the ground and which passes through the center of the wheel. If bearing C acts as a simple support and the effect of transverse shear due to P is negligible, determine the maximum force P (in kN) that can be applied to the wheel. Consider a factor of safety n = 2.5. Use the maximum energy of distortion failure criterion and do the analysis on bar AB (torsion bar) in the section where the bearing is.
The solid steel rod (1) has an allowable shear stress of 12 ksi. The brass tube (2) has an allowable shear stress of 5 ksi. The diameter of the rod is d1 = 0.625 in. The outside diameter of the tube is D2 = 1.625 in., and its wall thickness is t2 = 0.125 in. The tube is attached to a fixed plate at C, and both the rod and the tube are welded to a rigid end plate at B. Determine the largest torque Tmax that can be applied at the upper end of the steel rod.
15 M18 X4 Bolts F= 20 kN 60 D 60 |-75---75--| 50 250 A rectangular steelbar with 15 mm thickness attached to a 300 mm steel channelusing four tightly fitted bolts located at A, B, C, and D. For a F = 20 kN load find: (a) The resultant load on each bolt (FA, Fs, Fo, Fo=?) (b) The maximum shear stress in each bolt (T=?) (c) The maximum bearing stress occurred on the construction (OMAX=?) Note:All dimensions are given in mm unit.
While the ABCD rigid beam shown in the figure is simply supported from the A point, it is supported by vertical BF and CE bars from the B and C points, respectively. There is no tension in the bars in the unloaded condition. Considering that the length of the BF rod is 800 mm in addition to the given dimensions, if a strain value of -600 um / m unit occurs in the BF rod when a vertical P load is applied from the D end, the elongation amount in the CE rod will be the following in mm.