A pulley is supported by a circular pin at A. The pin has a diameter of d = 0.375 in., and each side of the pulley support bracket has a thickness of t= 0.1250 in. The average shear stress in the pin cannot exceed 40 ksi, and the bearing stress in the pulley support bracket cannot exceed 70 ksi. Determine the maximum value of Pmax that can be supported by the assembly. Pulley support bracket Answer: Pmax i ! kips %3D

A pulley is supported by a circular pin at A. The pin has a diameter of d = 0.375 in., and each side of the pulley support bracket has a thickness of t= 0.1250 in. The average shear stress in the pin cannot exceed 40 ksi, and the bearing stress in the pulley support bracket cannot exceed 70 ksi. Determine the maximum value of Pmax that can be supported by the assembly. Pulley support bracket Answer: Pmax i ! kips %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: For the diagram shown, if the load P = 14 kips, determine: a. the normal force in the member Bar BD…

A: Given data: the applied loadP=14 kipsthe diameter of the pin Bd=0.5 intotal length of the beamL=10…

Q: The composite shaft, consisting of aluminum, copper, and steel sections, is subjected to the loading…

A: Given data:- To find:- the displacement of B with respect to C the normal stress in each section

Q: A rod composed of an aluminum section rigidly attached between steel and bronze section. Axial loads…

A: Given data as per the question P=3000 lb Area of rod =0.5 in2

Q: Two wrenches are used to tighten the pipe. The pipe is made from a material having an allowable…

A: The maximum allowable shear stress is The outer diameter of pipe is The inner diameter is

Q: The pin-connected frame supports the loads P1 = 5 kN and P2 = 10 kN. Determine for an angle of α =…

Q: A force of 120 lb is applied to the edge of the member shown in the figure below. Neglect the weight…

A: given: P=120 lb Solution: Maximum bending moment is given as : Mmax=P×4.5=120×4.5=540 lb-in

Q: A cantilevered solid shaft with length of 400-mm and diameter of 150-mm is loaded at its free end as…

Q: The rectangular bar is connected to the support bracket with a 27-mm-diameter pin. The bar width is…

Q: Link AB, of width b= 2 in. and thickness t = in., is used to support the end of a horizontal beam.…

Q: A link is loaded as shown, it is attached with two bolts with a diameter of and its thickness is 0.1…

A: The diameter of bolt is The width of link is The thickness of link is The normal stress on link is

Q: For the clevis connection shown, the shear stress in the 5/16-in.-diameter bolt must be limited to…

Q: Question 3: The cast iron of a small press has a cross section as shown. For Q = 16-kips, determine:…

Q: A solid steel bar with a diameter of 50 mm is subjected to three forces as shown in the figure,…

A: In the given problem, the main stresses will be developed at point B due to 1200N force which will…

Question

100%

A pulley is supported by a circular pin at A. The pin has a diameter of d = 0.375 in., and each side of the pulley support bracket has a
thickness of t= 0.1250 in. The average shear stress in the pin cannot exceed 40 ksi, and the bearing stress in the pulley support bracket
cannot exceed 70 ksi. Determine the maximum value of Pmax that can be supported by the assembly.
Pulley support bracket
Answer: Pmax
i
! kips
%3D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Link AB, of width b = 2 in. and thickness t = 1414 in., is used to support the end of a horizontal beam. The average normal stress in the link is -18 ksi and the average shearing stress in each of the two pins is 12 ksi. Determine the average bearing stress (ksi). **The way I had solved it was that I used the given normal stress to first find the P force needed to plus into my bearing stress formula. I still however need the diameter. The answer key says to use the given shear stress equation to find the diamter, how do you know to use that and not the shear stress formula again?
When a force P of 750 N is applied to the pedal shown in the figure, find the diameter (mm) of this pin so that the resulting shear stress on the pin at C is 40 MPa.
NEED ASAP THANK YOU
Two loads P act as shown, one parallel to (x0) and another parallel to z0; each load P equals 2.5 kN. The crankshaft dimensions are b1 = 80 mm, b2 = 135 mm, and b3 = 55 mm. The diameter of the upper shaft is d = 26 mm. Determine the normal stress at point B, which is located on the surface of the upper shaft at the yo axis. Yo Хо b3 Lütfen birini seçin: a. 149.606 MPa b. 324.676 MPa c. 139.544 MPa d. None e. 190.884 MPa
2. If the allowable shear stress for each of the steel pins at A and B is tpe 6.5 ksi and the allowable normal stress for bar CB is Operm 10 ksi, determine the diameter of the pins at A and B and that of the square bar CB. Pin A is in double shear while Pin B is in single shear. Ignore points D and E. (^ } 2.5 ft -3 ft -5 ft 150 lb/ft Fx =
Solve the problems below: 1. The link acts as part of the elevator control for a small airplane. If the attached aluminum tube has an inner diameter of 25 mm and a wall thickness of 5 mm, determine the maximum shear stress in the tube when the cable force of 600 N is applied to the cables. 600 N 75 mm 5 mm 75 mm -25 mm 600 N
The 10-mm-diameter steel bolt in (Figure 1) is surrounded by a bronze sleeve . The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. Est = 200 GPa, Epr 100 GPa. Part A If the bolt is subjected to a compressive force of P = 15.7 kN, determine the average normal stress in the steel. Express your answer to three significant figures and include appropriate units. Ost = Value MPа Submit Request Answer Part B If the bolt is subjected to a compressive force of P = 15.7 kN, determine the average normal stress in the bronze. Express your answer to three significant figures and include appropriate units. Figure HA P Obr = Value MPа Submit Request Answer 10 mm Provide Feedback 20 mm P
A compression load of P = 55 kips is applied to a 2 in. by 2 in. square post, as shown. Determine the normal stress σn perpendicular to plane AB and the shear stress τn⁢t parallel to plane AB. Assume α= 30°.Calculate the normal force N perpendicular to the plane AB and the shear force V parallel to plane AB. Report both answers as positive numbers.Answers: N = kips, V = kips.
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ = 13 kips, F₂ = 34 kips, and the normal stress in each rod must be limited to 22 ksi, determine the minimum diameter d₁ required for rod (1). A (2) d₁ F₂ B C O 1.087 in. O 0.823 in. O 0.541 in. O 0.867 in. O 1.003 in. d₂
The principal strains at a point on the aluminum surface of a tank are P1 = 630(10-6) and P2 = 350(10-6). If this is a case of plane stress, determine the associated principal stresses at the point in the same plane. Eal = 10(103) ksi,nal = 0.33.
Part 1. A composite assembly of length, L-375 mm, consisting of a steel (G-77 GPa) core (2) connected by rigid plates at the ends of an aluminum [G-35 GPa) tube (1) is shown. The aluminum tube has outside diameter D₁ - 50 mm and inside diameter d₁-30 mm. = 100 MPa, and the The solid steel core has diameter d₂-25 mm. The allowable shear stress of aluminum tube (1) is (rallow) allowable shear stress of steel core (2) is (Tallow)2= 135 MPa. Determine (a) the allowable torque T that can be applied to the composite shaft. (b) the corresponding torques produced in tube (1) and core (2). (c) the angle of twist produced by the allowable torque T. T D₁ L Calculate the polar moment of inertia, J₁, of the aluminum tube. Answer: J₁ (106) mm².
When a force P of 750 N is applied to the pedal shown in the figure, find the diameter (mm) of this pin so that the resulting shear stress at the pin C is 40 MPa.