Q1 (DÖÇ-1) In the given structure, the link BD has rectangular cross section of 18 mm × 8 mm, the diameter of the pin at C is 6 mm and the diameter of the pins at B and D is 10 mm. If the failure shear stress for the pins is 160 MPa and the failure normal stress for the link BD is 420 MPa determine the largest load P that can be applied. 35 mi -18 mm Note: Factor of Safety : 3.0 AC The pins at B and D are subjected to single shear and the pin at C is subjected to double shear 160 mm 120 mm

Q1 (DÖÇ-1) In the given structure, the link BD has rectangular cross section of 18 mm × 8 mm, the diameter of the pin at C is 6 mm and the diameter of the pins at B and D is 10 mm. If the failure shear stress for the pins is 160 MPa and the failure normal stress for the link BD is 420 MPa determine the largest load P that can be applied. 35 mi -18 mm Note: Factor of Safety : 3.0 AC The pins at B and D are subjected to single shear and the pin at C is subjected to double shear 160 mm 120 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem 10. The A-36 steel plate has a thickness of 12 mm. If there are shoulder fillets at B and C, and O allow = 150 MPa, determine the maximum axial load P that it can support. The maximum stress at the fillets can be determined from the formula Omax = K Gave, where K is the stress concentration factor for fillets given in Graphs in Section 4.7 of Hibbeler textbook, and based on the fillet radius to small width and large width to small width ratios. Also compute its elongation neglecting the effects of the fillets. 60 mm P A B r = 30 mm 200 mm 120 mm 800 mm r = 30 mm 200 mm 60 mm P
If the allowable tensile stress for the bar is (ot)allow = 20 ksi, and the allowable shear stress for the pin is Tallow = 11.6 ksi. Assume the hole in the bar has the same diameter d as the pin. Take t = 1/4 in. and w = 2 in. (Figure 1) Figure w/2 [w/2 P 1 of 1 > Part A Determine the diameter of the pin so that the load P will be a maximum. Express your answer to three significant figures and include appropriate units. d= Submit Part B P = Submit μA Value Request Answer What is this maximum value for P? Express your answer to three significant figures and include appropriate units. li μA Provide Feedback Value Units Request Answer ? Units ?
The bolted connection shown in the figure is subjected to a tensile shear load of 100 kN. The bolts are ISO class 5.8 and the material is cold-drawn AISI 1040 steel. Find the factor of safety of the connection for all possible modes of failure. 35 - 35 15 M20 x 2.5 35 35 - 20
The bolt AB in (Figure 1) has a diameter of 18 mm and passes through a sleeve that has an inner diameter of 42 mm and an outer diameter of 52 mm. The bolt and sleeve are made of A-36 steel and are secured to the rigid brackets as shown. If the bolt length is 220 mm and the sleeve length is 200 mm, determine the tension in the bolt when a force of 50 kN is applied to the brackets.
1. A solid square rod is cantilevered at one end. The rod is 0.8 m long and supports a completely reversing transverse load at the other end of 50 kN. The material is AISI 1060 hot-rolled steel (?? =370 MPa,?? =680 MPa ). Use a design factor of 2 and determine the dimensions of the square cross section for the following cases. Neglect any stress concentration. a. The rod must support this load for 100 cycles. b. The rod must support this load for 104 cycles. c. The rod must have infinite life.
A bolted lap joint using ISO 5.8 bolts and members made from cold-drawn SAE 1040 steel is shown in the figure. Assume the bolt threads do not extend into the joint. Find the tensile shear load F that can be applied to this connection to provide a minimum factor of safety of 2.5 for the following failure modes: shear of bolts, bearing on bolts, bearing on members, and tension of members. 40 ↑ 70 40 ↑ 80 M20 × 2.5 20 20
Two metal bars are fastened together at the bolted flange connection shown. There are 2 total bolts 12.7 mm. The flange is - connecting the two metal bars together and each bolt has diameter dbolt oriented at angle 55° with respect to longitudinal axis of the metal bars. If an axial force F = 40 kN is applied as shown, determine the overall safety factor of the bolted connection. You may assume the bolts are made out of 1020HR steel and the strength of the bolt in shear is 50% of the tensile strength of the bolt material. SF overall F = = 2.576 Ꮎ ? X 0% = F
The assembly shown in Figure 5 consists of two sections of galvanized steel pipe connected using a reducing coupling at B. The smaller pipe AB has an inner diameter of d 16 mm and an outer diameter of do 18 mm, whereas the larger pipe BC has an inner diameter of d = 21 mm and an outer diameter of dae #24 mm. Take LAB= Lec 250 mm and G = 25 GPa. If the pipe is tightly secured to the wall at C. determine the angle of twist at point A A LAB 75 N 150 mm- 200 mm Lac 75 N 022
Problem 17 A joint shown has the basic layout shown in the diagram below. (All dimensions on the diagram are in inches.) A single pin of diameter 0.5 inches (A = 0.2 in2) holds together the yoke and bar as shown. The material has an ultimate strength in tension of 80 ksi, and an ultimate strength in shear of 45 ksi. The load P has a value of 10000 lb. By examining the shear stress in the pin, the normal stress in the yoke, and the normal stress in the bar, find the overall factor of safety for the joint. P=10,000 lb YOKE -0.5 PIN BAR P=10,000 lb 1.5- 20 1.5 0.5 0.5
• Bars (1) have a cross-sectional area of A₁ = 0.65 in.2 and a length, L₁= 7 ft. • Bars (1) are made of cast iron with an elastic modulus of E₁ = 24,000 ksi, a coefficient of thermal expansion, a₁ = 12.3 x 10-6/°F and yield strength of oy = 120 ksi. • Bar (2) has a cross-sectional area of A₂ = 1.45 in.² and a length, L₂ = 5.5 ft. • Bar (2) is made of stainless steel with a coefficient of thermal expansion, a₂ = 10.6 × 10-6/°F. • The stress-strain diagram provided below presents the results of the stainless steel's (i.e., Bar (2)) bar tension test. • There is a gap of A = 0.1 in. in the connection at B and a = 3 ft. • All bars are unstressed before a load P = 12 kips is applied and the temperature increases by AT = 40°F. Stress-strain diagram for stainless steel bar: (1) a Stress (ksi) L2 Rigid bar 120 100 80 60 40 20 0 0 0 B (2) P a (1) C Upper scale L₁ Connection details at node C Lower scale. C 0.025 0.050 0.075 0.100 0.125 0.150 0.175 0.006 0.008 0.010 0.012 0.014 0.002 0.004 Strain…
FBD 3. Determine the required thickness of member BC and the diameter of the pins at A and B if the failure normal stress for member BC is Ofail = 30 ksi, and the failure shear stress for the pins is Tfail = 12 ksi. Use a safety factor of 1.2 to your design. Solution: 1.5 in. 60° 8 ft 5 kip/ft