Part AThe lever is attached to the shaft A using a key that has a width d and length of 26 mm .If the shaft is fixed and a vertical force of 200 N is applied perpendicular to the handle, determine the dimension d if the allowable shear stress for the keyis T = 37 MPa(Figure 1)Express your answer with the appropriate units.HAd =ValuemmSubmitRequest AnswerProvide FeedbackNext >Figure< 1 of 1 >d-20 mm500 mm200 N

Given F = 200 N Width = d Length (L) = 26 mm Shear stress = 37 MPa

Answered: The lever is attached to the shaft A…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The drive shaft AB of an automobile is to be designed as a thin-walled tube. The engine delivers 150 hp when the shaft is turning at 1000 rev>min. Determine the minimum thickness of the shaft’s wall if the shaft’s outerdiameter is 2.5 in. The material has allowable shear stress of tallow = 7 ksi.
Part A The A 30 stoel boit is tightened within ia hole so that the reactive torque on the shank ABcan bo exprotsed by the equation f (kz)N m/m, whem zn meters A torque of T-50N mis ppled to the bol heed Assume the shank has a constant radius of 6 mm The shear modulus tf elasticity for A.36 sleel is 15 GPa (En.1) Determine the constant k Express your answer using three significant figures. V A veo Submit Renunst Answer Figure Part B Deteemne the amount of twrst in me 50 nm ength or me snan Express your answer using three significant figures Va AL vec Tad Submit Besuest AnswE Activate Windows Pearson
FkN dl mm dl mm 10 mm 10 mm d2 mm 10 mm d2 mm The column is subjected to an axial force(F) of 11 kN at its top. If d1 = 71 mm and d2 = 60 mm determine the average normal stress (o MPa) at the section a-a;
A motor delivers 500 hp to the shaft, which is tubular and has an outer diameter of 2 in. If it is rotating at 200 rad>s, determine its largest inner diameter to the nearest 1 8 in. if the allowable shear stress for the material is tallow = 25 ksi.
The rigid bar AB and CD are supported by pins at A and D. the vertical rods are made of aluminum and bronze. Determine the vertical displacement of the point where the force P= 10 kips is applied. Neglect the weight of the members.
Q3 Design the square key which is located on the shaft motor if the diameter of it is (20) mm and shearing and crushing stresses which applied of it are 200N/mm and 400N/mm' respectively ,When the ?force applied on the key equal to (10 000) N
Please help. Given below are the complete informations to solve the problem. Please answer in the format of given, required, solution in detailed.
The 2-m-long tube is made of an elastic perfectly plastic material as shown. Determine the applied torque T, which subjects the material at the tube’s outer edge to a shear strain of gmax = 0.006 rad. What would be the permanent angle of twist of the tube when this torque is removed? Sketch the residual stress distribution in the tube
10
04 It is required to find the dimensions of thick cylinder which has internal diameter of (150+SN) mm (find the thickness and external diameter). External pressure is zero. Knowing that the ratio between the internal pressure to maximum hoop stress is 0.4. Also find the change in thickness of the metal when the internal „pressure is 500 bar. Take E=210 MN/m2 and v-0.3 SN= 32
1-63.M. The key in Figure 1-18 has the dimensions b = 10 min, h = 8 nim, and L = 22 min. Determine the shear stress in the key when 95 N-m of torque is transferred from the 35-mm-diameter shaft to the hub. Hub End view Shear plane Shear pl T=Torque -D=Shaft diameter T=F(D/2) F₁-Force of shaf F₂= Force of hub on 1 Shear area=A,=bxL
do not round it off please until the end

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS