A lever is attached to a shaft with a square shear key as shown. The force applied to the lever is P- 525 N. If the shear stress in the keymust not exceed 73 MPa, determine the minimum dimension "a" that must be used if the key is 17 mm long.- Shear key700 mm42 mmShear key detailO 19.09 mmO 16.39 mmO 17.87 mmO 14.10 mmO 15.16 mm

Answered: Image /qna-images/answer/1d2ba049-537d-4142-9fdd-01653a9eb02c.jpg

Answered: A lever is attached to a shaft with a…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1. A (50) mm diameter shaft is made of steel with a yield strength of 440 MPa. There are two parallel keys available A (w = 10 mm, t 8 mm, L= 90 mm) and B (w 12 mm, t = 10 mm, L = 100 mm), suggest one of them to connect a pulley with the shaft. Use factor of safety (4). Assume the key has the same material of the shaft and the tensile and the compression stresses are equal.
The thickness of the plate is t and the diameter of the pin is d. What is the correct area formula for determining the bearing stress between the pin and the steel plate? P pin Steel plate Support W
A gear motor can develop 2010 W when it turns at 231 RPM. If the allowable shear stress for the material of the shaft connected to it is Tallow = 88.3 MPa, determine the smallest diameter of the shaft to the nearest mm that can be used. 14 mm 21 mm 22 mm 9 mm 17 mm 2 mm
The compound bar is composed of brass and copper. It supports the axial loads shown below. Determine the stresses developed on both materials. Indicate whether the stress is tensile or compressive Answer: σbr = ___________________σco = ___________________
Downvote for incorrect answer The connection is made using a bolt and nut and two washers. If the allowable bearing stress of the washers on the boards is (b)allow 2 ksi, and the allowable tensile stress within the bolt shank S is (allow 18 ksi, determine the maximum = allowable tension in the bolt shank. The bolt shank has a diameter of 0.31 in., and the washers have an outer diameter of 0.75 in. and inner diameter (hole) of 0.50 in.
please help
The bolted connection carries a load as shown. What is the minimum size of the bolt if the allowable shearing stress is 32 Mpa? The spacing between adjacent bolts is 50 mm and the distance between the force and the nearest bolt is 247mm
Part A -80 mm- P 75 mm -40 mm 30 mm If the bolt head and the supporting bracket are made of the same material having a failure shear stress of Tfail = 150 MPa, determine the maximum allowable force P that can be applied to the bolt so that it does not pull through the support. Apply a factor of safety of F.S. = 2.5 against shear failure. Express your answer to three significant figures and include the appropriate units.
Only do the safety factor part
If the block is loaded with P = 257 kN, calculate the required dimension "h" of the key. Write your final answer in 2 decimal places with the unit of mm.
y A B 3 in. D C 2 in. -2 in. 1.5 in. E.
Only Handwritten solutions are allowed. No Chatgpt, you must have to draw the free body diagram.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS