Part A If the bolt head and the supporting bracket are made of the same material having a failure shear stress of Tfail = 150 MPa, determine the maximum allowable force P that can be applied to the bolt so that it does not pull through the support. Apply a factor of safety of F.S. = 2.5 against shear failure. Express your answer to three significant figures and include the appropriate units.

Part A If the bolt head and the supporting bracket are made of the same material having a failure shear stress of Tfail = 150 MPa, determine the maximum allowable force P that can be applied to the bolt so that it does not pull through the support. Apply a factor of safety of F.S. = 2.5 against shear failure. Express your answer to three significant figures and include the appropriate units.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. From the given assembly, compute the safe load P that can carry. Given that the allowable deformation is 2mm only
1. w2011 30cm day 50 cm Link BC is circular rod of 1.2 cm diameter and made of a material with an ultimate normal stress of 100 MPa. Using a factor of safety of 3.1, what is the maximum P value for which the allowable normal stress in BC will not be exceeded?
The 5-inch diameter uniform bar is made from steel and supports the following axial loads. Determine the maximum safe value of force P that may be applied if the tensile and compressive stresses are limited to 1250 psi and 1000 psi, respectively. Answers: P = ___________________
' Three piates are joined with a 12-mm diameter pin as shown beiow. Determine the maximum load p that can be transmitted by the joint if the maximum bearing stress between a plate and the pin must be limited to 650 MPa .
The ultimate shear strength of the bolts is 250 MPa, and a factor of safety of 2 is required. Determine the minimum required bolt diameter to resist an applied load ofP = 1,300 kN. Support Bar
If load P = 23.5 kips, determine the normal force in bar (1). (1) P A O 39.2 kips O 35.7 kips O 49.6 kips O 32.4 kips O 24.1 kips 6 ft B 4 ft
Rigid bar ABC is supported by bronze rod (1) and aluminum rod (2), as shown. A concentrated load P is applied to the free end of aluminum rod (3). Bronze rod (1) has an elastic modulus of E₁ = 15,000 ksi and a diameter of d₁ = 0.40 in. Aluminum rod (2) has an elastic modulus of E₂ = 10,000 ksi and a diameter of d₂ = 0.70in. Aluminum rod (3) has a diameter of d3 = 1.00in. The yield strength of the bronze is 48 ksi and the yield strength of the aluminum is 40 ksi. Assume a = 2.5 ft, b = 1.5 ft, L₁= 6 ft, L₂= 8 ft, and L3 = 3 ft. (a) Determine the magnitude of load P that can safely be applied to the structure if a minimum factor of safety of 1.8 is required. (b) Determine the deflection of point D for the load determined in part (a). (c) The pin used at B has an ultimate shear strength of 57 ksi. If a factor of safety of 2.7 is required for this double shear pin connection, determine the minimum pin diameter that can be used at B. L₁ T A Bronze (1) B Aluminum (3) D Aluminum P b (2) L3 •…
Two steel plates are held together by two bolts. (/6) a. Determine the required diameter of the bolts if the failure shear stress is 300 MPa using a Factor of Safety (FS) of 2. b. Using the answer from a. above, determine the steel plate thickness if the failure bearing stress of the steel is 350 MPa using FS = 1.5. Show your work. OKN Two Bolts P=60KN
If load P = 22.9 kips, determine the normal force in bar (1). D P A 6 ft 51.9 kips 44.8 kips 27.3 kips 38.2 kips O 40.4 kips B (1) 4 ft
Q1. A (50) mm diameter shaft is made of steel with a yield strength of 440 MPa. There are two parallel keys available A (w = 10 mm, t 8 mm, L= 90 mm) and B (w 12 mm, t = 10 mm, L = 100 mm), suggest one of them to connect a pulley with the shaft. Use factor of safety (4). Assume the key has the same material of the shaft and the tensile and the compression stresses are equal.
σ(allowable) = 243,000 psi Factor of safety = 1.5 Allowable shear stress (τ) = ?
- once answered correctly will UPVOTE!!