If load P = 22.9 kips, determine the normal force in bar (1). D P P A 6 ft 51.9 kips 44.8 kips 27.3 kips 38.2 kips 40.4 kips B (1) 4 ft

Q: If load P = 20.1 kips, determine the normal force in bar (1). A 6 ft 46.6 kips 39.5 kips 33.5 kips…

A:

Q: Period: This bridge spans a 10ft wide creek. A 30lb downward force is located at the top center of…

A: To Find :  The x and y components, what is the load and the T or C for each member. Given:  The load…

Q: Compute the allowable load in kN on a 20mm x 120cm long steel rod with a maximum elongation must not…

A:

Q: Q2. Rigid member DEF is supported by three rods, AD, BE, and CF, and the rods are of the same…

A:

Q: A round steel bar with a diameter of 1.500 in is subjected to the axial loads shown. P1 = 95 k, P2 =…

A: According to the given data P1=95kips P2=115kips Diameter = 1.5in For steel E= 29000ksi Length of…

Q: Determine the smallest coefficient of static friction at both A and B needed to hold the uniform…

A:

Q: Determine the force in each member of the Pratt roof truss shown in Figure 1-94. 10 kN 10 kN 10 kN B…

A:

Q: Required Information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A: L= 1.2 kN To find - The forces in members.

Q: + The forces are given in figure and applied as shown. 3 F,-100 KN Fq= 50KN and F3= 30 KN. The…

A: The main difference between twisting moment and bending moment is that their directions of moment.…

Q: 10 b 15 in. 15 in. poccor D 30° 10 b TO P

A: To findWhat is the minimum tension P of the cord?What is the orientation, ?Given     the resultant…

Q: 1.5 m 1.5 m 1.5 m PV B -2 m – -2 m –

A: Given , P = 10 KN

Q: Determine the magnitude of the pin force at A. Assume W = 795 lb, a = 2.9 ft, b = 2.2 ft, r = 7 in.…

A:

Q: 3) Determine the force in each cable needed to support the 500 N load. (Ans: FCA=197.5N; FeB=197.5N;…

A: First, draw the free-body diagram of the structure and calculate the corresponding components of the…

Q: 8. A concrete wall footing With a Width or and a depth of 0.6 m supports a centrally placed…

A: Given: Ultimate bearing stress is 475 kN/m2. Factor of safety is 5. weight density of the concrete…

Q: Suppose that P = 2000 lb. (Figure 1) Figure B -4 ft H 4 ft K 4 ft 1 of 1 3 ft ▼ Determine the force…

A: Take, P =2000 lb To find - The force in members DE, DF and GF of the cantilevered truss.

Q: Determine the force in member AD and state if the member is in tension or compression Express your…

A:

Q: 1,200 N-m 4,500 N-m 2,800 N-m 500 N-m (3) B 0.70 m 1.80 m 0.70 m Complete the torsion diagram of rod…

A:

Q: Rigid bar AD is horizontal before the weight of radius of 0.025" and are made of A913 steel.…

A: E=200GPaE=29007547.58 psiTension developed in wire BC,TBC=WTBC=112 lbTension developed in wire…

Q: 2.4 <-0.9 B 1.8 Dimensions in meters C. D. 1.8 Determine the value of the maximum load W if the…

A: According to the given dataco-ordinates of…

Q: Problem 2 You will be determining the value for the external load P that will cause the diameter of…

A:

Q: Link BD consists of a single bar 1 in. wide and in. thick. Each pin has a -in. diameter and P= 7…

A: GivenFor bar BDw=1int=12indp=38inP=7kipsWhenθ=90o

Q: 5 in. 8 in. A Two bars are used to support a load P. When unloaded, AB is 5 in. Iong, AC is 8 in.…

A:

Q: 2. Two initially rigid bars AC and DG are pinned at A and G and are also connected by vertical bars…

A: Step 1:  Step 2:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.