In the steel structure showm in the figure, a 6 mm diameterpin is used at C and 10 mm diameter pins are used at B andD. The shear stress limit is 150 MPa in all connections, andthe normal stress is 400 MPa at bar BD. Knowing that afactor of safety of 3.0 is desired, determine the largest loadP that can be applied at A. Note that bar BD is notreinforced around the pin holes.DFRONT VIEW80mm-22 mm5 mm2kN/mВBSIDE VIEW210 mm150 mmPAUPPER VIEW

Answered: Image /qna-images/answer/40bcedc1-71d9-447a-8ca9-ac30e27e12f6.jpg

n the steel structure shown in the figure, a 6 mm diameter in is used at C and 10 mm diameter pins are used at B and ). The shear stress limit is 150 MPa in all connections, and he normal stress is 400 MPa at bar BD. Knowing that a actor of safety of 3.0 is desired, determine the largest load that can be applied at A. Note that bar BD is not einforced around the pin holes.

n the steel structure shown in the figure, a 6 mm diameter in is used at C and 10 mm diameter pins are used at B and ). The shear stress limit is 150 MPa in all connections, and he normal stress is 400 MPa at bar BD. Knowing that a actor of safety of 3.0 is desired, determine the largest load that can be applied at A. Note that bar BD is not einforced around the pin holes.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.5.25P: A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just...

See similar textbooks

Similar questions

A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
The axial stresses are 12 MPa C in the wood post B and 150 MPa T in the steel bar A as shown below. Pins at A, C, and D are smooth. Determine (a)The load P.(b)The minimum diameter for pin C if it is in single shear and the cross-shearing stress is limited to 70 MPa.(c)The minimum diameter for pin D if it is in double shear and the cross-shearing stress is limited to 70 MPa.
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. A 2 kip/ft distributed load is applied on member AB, which is supported by a pin at A and bar BC. The connections at points A and B are shown in detail. All pins have a diameter of 0.5 in while all members have cross-sectional dimensions of 1.5 x 1 in. Determine the following:a. maximum normal stress in member BC (ksi)b. normal and shear stress in a horizontal section across member BC apart from the pin (ksi)c. shear stress in pins A and B (ksi)d. maximum bearing stress on member AB (ksi)
Observe the figure that shows the assembly of the ACD arm, suspended by a bearingin C coupled to a horizontal rod in A. The arm supports a load of 4 kN applied at theend D. Considering that the allowable shear stress of the material of the pin in bearing C is30 MPa, what is the diameter of pin C, which supports the 4 kN load? What is theelongation of the steel bar AB (E= 200 GPa) with a diameter of 20 mm? BA length 300mm
The lap joint is fastened with four 3/5 in-diameter rivets. The allowable normal stress in the plates is 30 ksi, allowable shearing stress is 24 ksi for the rivets and 28 ksi for the plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets. Include the necessary FBDs showing the involved internal forces in the exploratory sections. Your solutions are invalidated without the required FBDs.
(4) The plunger of an oil pump is held against the operating cam by a spring made of No.10 W&M gage steel wire coiled with an outside diameter of ⅞-in. There are five active coils. The open length is 1.1875in. What are the length & stress when a load of 30lb is applied.
An aluminum alloy cylindrical roller with diameter 1.25 in and length 2 in rolls on the inside of a cast-iron ring having an inside radius of 6 in, which is 2 in thick. Find the maximum contact force F that can be used if the shear stress is not to exceed 4000 psi.
The lap joint is fastened with four ¾-inch diameter rivets. a. If the allowable shearing stress of the rivets is 14 ksi (kips per square inch), find the value of P (kips) that maybe applied to the joint. Assume that the load is equally distributed among the rivets. b. if the allowable bearing stress for the plates is 18 ksi, find the value of the load P (kips) that maybe applied to the joint. Assume that the load is equally distributed among the rivets. c. what is the maximum value of the load P (kips) that can be applied to the joint?
A bronze bar is fastened between a steel bar and an aluminum bar as shown in Fig. Axail loads are applied at the positions indicated. Find the largest value of P that not exceed an overall deformation of 0.1 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembley is suitablly barced to prevent buckling. Use E = 200 GPa for steel, E=83 GPa for bronze, and E= 70 GPa for aluminum. Steel A= 480 mm² Bronze A = 650 mm² Aluminum A = 320 mm² 3P 4P 2P 1.0 m 1.5 m P = 12.8 KNO P = 6.8 KN P = 1.4 KN P = 0.4 KN 2.0 m
1. A bronze bar is fastened between a steel bar and an aluminum bar as shown. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use EsT=200GPA, EAL = 70 GPa, and EBr = 83 GPa. As = 480 mm? Ab=650 mm? Al= 320 mm? 2P 4P 3P 1m 2m 1.5m
The lap joint shown is fastened by 4 rivets of ¾ in. diameter. Find the maximum load P that can be applied if the working stress are 14000 psi for shear in the rivet and 18000 psi for bearing in the plate. Assume that the applied load is distributed evenly in the 4 rivets. The plate is 7/8 in. thick and 4 in wide.