Required information Two solid cylindrical rods AB and BC are welded together at 8 and loaded as shown. Take di = 30 mm, d₂ = 50 mm, and P = 85 KN. 0.9 m 125 AN 125 IN 12 m Find the average normal stress at the midsection of rod BC. (Input the answer with the appropriate sign.) The average normal stress at the midsection of rod BC is | MPa.

Required information Two solid cylindrical rods AB and BC are welded together at 8 and loaded as shown. Take di = 30 mm, d₂ = 50 mm, and P = 85 KN. 0.9 m 125 AN 125 IN 12 m Find the average normal stress at the midsection of rod BC. (Input the answer with the appropriate sign.) The average normal stress at the midsection of rod BC is | MPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Part A The lever is attached to the shaft A using a key that has a width d and length of 26 mm .If the shaft is fixed and a vertical force of 200 N is applied perpendicular to the handle, determine the dimension d if the allowable shear stress for the key is T = 37 MPa (Figure 1) Express your answer with the appropriate units. HA d = Value mm Submit Request Answer Provide Feedback Next > Figure d -20 mm 500 mm 200 N
A column is fabricated by adhesively bonding two aluminum faceplates to a foam plastic core as shown below. Note that there are only left and right aluminum plates (with no front and back plates). The foam plastic core has a square cross-section with elastic modulus Ef 1110 MPa. Determine the stress in the aluminum plates, the stress in the foam core, and the displacement of the column under the action of the applied force. = Note: Express tensile stresses as positive (+) and compressive stresses as negative (-). Given: • L1 L2 = = 100 mm = 1.7 m • . L3 = = 1.4 mm RIGID PLATE ALUMINUM FACE PLATE F FOAM L2 |← 41 +| |—–—– 63 L1 L3 F = 37 kN σα = σ f = |ɗ| = = number (rtol=0.01, atol=1e-05) number (rtol=0.01, atol=1e-05) number (rtol=0.01, atol=1e-05) MPa ? MPa mm ?
4. The stepped circular bar shown below is made from aluminum (E = 70 GPa, v = 0.35). Each segment is 400 mm in length. Prior to applying the loads, the bar has the dimensions shown. The structure is axially loaded as shown. Determine the stress in each segment, the maximum stress and its location, the final in length of the structure, and the final diameters of each segment due to the applied loads. All dimensions shown are in mm. Ø 25 40 15 ↑ Fu 300 kN 600 kN 300 kN
The state of plane stress shown occurs at a critical point of a metal machine component. As a result of several tensile tests, it has been found that the tensile yield strength is Fy for the grade of metal used. Determine the ratio of OT/ OH shown in the figure, using the maximum-shearing-stress criterion (Tresca Hexagon). (Using Mohr circle method to calculate principle and average stresses) OX TXy Mpa Mpa Mpa MPa ob σy тху 90 -60 45 310 dy OX x Sx=Sx Sy=sy txy=txy Fy=Yield Strength Answer
Three metal rods are firmly attached to the walls and the middle rigid plate. Rod AB is made from stainless steel and rods CD and EF are made from 2014-T6 aluminum. If a balanced load is applied to the rigid plate, determine what the stresses are in the rods. Follow the sign convention that tensile stress is positive and compressive stress is negative. The parameter values are listed in the table above the figure. A parameter value units 470 mm 400 mm 40 mm 30 mm 30 KN cc 080 BY NO SA 2021 Cathy Zupke L₁ L2 d₁ d₂ P 4₁ B C E The stress in AB σAB= The stress in CD and EF: OCD = EF= d₂ L₂ MPa D F MPa
Question 5: The following 0.8" diameter steel bar has three loads applied, as shown. Assuming that E= 30,000,000 psi, determine the following: Stress at points A, B, and C Total elongation of the bar. Hint: 8- PL AE オー 2000 Ibs 2-0" 4000 Ibs I-0 7000 Ibs
If the allowable tensile stress for the bar is (ot)allow = 20 ksi, and the allowable shear stress for the pin is Tallow = 11.6 ksi. Assume the hole in the bar has the same diameter d as the pin. Take t = 1/4 in. and w = 2 in. (Figure 1) Figure w/2 [w/2 P 1 of 1 > Part A Determine the diameter of the pin so that the load P will be a maximum. Express your answer to three significant figures and include appropriate units. d= Submit Part B P = Submit μA Value Request Answer What is this maximum value for P? Express your answer to three significant figures and include appropriate units. li μA Provide Feedback Value Units Request Answer ? Units ?
Question: Consider that the fit between the elements shown in the Figure below is H6/s5. They are both made of SAE 1340 OQT 1000 steel (Sy= 950 MPa, E = 200 GPa). Take D; = 75 mm and D, %3D %3D 90 mm. Determine the maximum possible value of the tangential stress at the inner surface of the outer element in MPa. NOTE: Answer is not 4750MPA. If you Submit This answer I will Directly report. |D, H6/s5 D. 6/7
Determine the state of stress acting at point D. Take P₁ = 120 kN and P₂ = 45 kN. (Figure 1) Figure L -1.5m- +1.5m-1.5 m- 0.5 m 40 mm 100 mm 60 mm 80 mm 1 of 1 > Find op- Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. od= - 154.88 Submit Part B Previous Answers Request Answer X Incorrect; Try Again; 3 attempts remaining MPa Find TD- Express your answer to three significant figures and include the appropriate units. JA TD= Value Units ?
Determine the maximum axial force that can be applied to the bar shown in Figure 3. The allowable stress is 100 MPa. The dimensions are: Hole diameter 20 mm. Thickness of bar: 6 mm D = 40 mm d%3D20mm Fillet radius, r = 4 mm 40mm 20 mm r 4 mm 20 mm Figure 3 P.
Problem 2 You will be determining the value for the external load P that will cause the diameter of BC to change to 5.8 mm. The original diameter of BC is 6 mm. Use the values given below unless otherwise stated by the questions. E = 200 GPa V = 0.38 300 mm 400 mm B 1 -200 mm-
The bar is made from steel and has an allowable stress of allow = 19.7 ksi (Figure 1) Figure P 1.875 in. 0.75 in. -0.125 in. 1.25 in. r 0.25 in. 1 of 1 Part A Determine the maximum axial force P that can be applied to the bar. Express your answer to three significant figures and include the appropriate units. P = Submit μA Value Request Answer < Return to Assignment Units Provide Feedback ?