The pin is used to connect the three links together. Due to wear, the load is distributed over the top and bottom of the pin as shown on the free-body diagram. The diameter of the pin is d= 0.39 in. (Figure 1) Determine the maximum bending stress on the cross section at the center section a-a. Hint: For the solution it is first necessary to determine the load intensities w₁ and 2

Q: The way to the column where the loading status is seen determine the P load required for the 5 mm…

A: Given that,

Q: What is the vertical displacement at joint F. Assume all members are pin connected at their end…

A:

Q: 4) The water pump in the Figure maintains a pressure of 6.5 psig at point 1. There is a filter, a…

A: Below is the clarified and detailed explanation for above tricky question....if you are ok with my…

Q: A laminated wood beam consists of six 2 x 6 in planks glued together to form a section 6 in wide by…

A: Strength of glue in shear = 120psi Find the maximum uniform distributed load

Q: Provide final answer and equations used.

A:

Q: A certain type of piping system uses deformable rings to clamp pipes onto fittings. A crimping tool…

A:

Q: Determine moment that will produce a maximum stress of 60 MPa on the cross section. To 3 significant…

A:

Q: The beam is supported by double-shear pins at A, B, and C. The radius of all the pins are r = 8 mm.…

A: Find outDetermine the magnitude of the normal force in rod BC, .Determine the magnitude of the…

Q: ing a The rigid beam is supported by a pih at A and tWo steel wi If the yield stress for the wires…

A: Givenσy=530MPaEst=200GPad=4mmL=800mm

Q: *4-28. The rod has a slight taper and length L. It is suspended from the ceiling and supports a load…

A: For the given taper rod, load P is applied at the end. E = modulus of elasticity of the rod material…

Q: The pipe assembly is subjected to the loads shown. Determine the state of stress at point A on…

A: Given data, Let Ax, Ay and Az are the reaction force at A Bx and Bz are the reaction force at B Cz…

Q: A metal bar is made out of A-36 steel and has a diameter d = 23mm with the end at A fixed to the…

A: To findCalculate the displacement of point C relative to point A.Givendiameter, d = 23 mmLoad, Load,…

Q: shift is subjected to the axial loads shows. If copper has an E=18×10^6Psi and the diameters of each…

A:

Q: The bar is connected to the support using a pin having a diameter of d =lin. If the allowable…

A:

Q: F=(X+4) kN |B L=Y+1 m L=Y+1 m S=1YX mm 30 mm 1 H=2X0 mm -H- 300mm - - 30 mm 30 mm 30 mm The…

A: The maximum load P that can be applied to the load end of the beam is 8.6 kN.

Q: Determine the reaction forces R1 and R2 and show the shear and bending moment diagram. Data: Point…

A: To find: The reaction forces. FBD: The free-body diagram is shown below.

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.