The bar is connected to the support using a pin having a diameter of d =lin. Ifthe allowable tensile stress for the bar is (o,)low = 20ksi , and the allowable bearing stressbetween the pin and the bar is (0,)allow= 30ksi , determine the dimension w and t so thatthe gross area of the cross section is wt = 2in² and the load P is a maximum. What is thismaximum load? Assume the hole in the bar has the same diameter as the pin. (Hint: Usethe prjjected area whenj calculating the bearing stress.)tdw/2w/2

Answered: Image /qna-images/answer/a228a797-3d30-4ce5-96a6-cc38daea6bf8.jpg

The bar is connected to the support using a pin having a diameter of d =lin. If the allowable tensile stress for the bar is (o,),allow = 20ksi , and the allowable bearing stress between the pin and the bar is (o,)llow = 30ksi , determine the dimension w and t so that %3D the gross area of the cross section is wt =2in? and the load P is a maximum. What is this maximum load? Assume the hole in the bar has the same diameter as the pin. (Hint: Use the projected area when calculating the bearing stress.) d- w/2 w/2

The bar is connected to the support using a pin having a diameter of d =lin. If the allowable tensile stress for the bar is (o,),allow = 20ksi , and the allowable bearing stress between the pin and the bar is (o,)llow = 30ksi , determine the dimension w and t so that %3D the gross area of the cross section is wt =2in? and the load P is a maximum. What is this maximum load? Assume the hole in the bar has the same diameter as the pin. (Hint: Use the projected area when calculating the bearing stress.) d- w/2 w/2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The rod BD is made of material with G1= 124 GPa has a diameter 34 mm is bonded to the tube CA at point B, the tube made of material with G2=211 GPa has an outer diameter 73 mm and wall thickness of 10 mm. If T1=579 N.m and T2=1042 N.m, answer the following questions: The maximum shear stress of the rod BD is The maximum shear stress of the tube CA is The maximum shear stress of the assembly is The angle of twist between D and B is The angle of twist between C and A is The angle of twist at D is Your answer The angle of twist between C and B is Your answer The reaction at point A is
Three round bars welded together are axially loaded as shown. Find the normal stress in each bar if P=15 kN
A4
Q: The aluminum bar of circular cross section is attached to rigid supports at A and C. Calculate the maximum stress in each segment after the load (30 kN) is applied. Use E = 70 GPa. .400 mm- 250 mm- 30 kN 100 mm 50 mm
The circular column is subjected to a compressive force of 5kN if the stress in the column is limitedto 17.63MPa, what is the limiting value of diameter d?
Find the stress in the rod having a diameter of 20 mm, subjected to 10 kN force. If the material of the rod is steel (E = 200 GPa), what is the change in length of the rod?
Need Step wise solution
A column is fabricated by adhesively bonding two aluminum faceplates to a foam plastic core as shown below. Note that there are only left and right aluminum plates (with no front and back plates). The foam plastic core has a square cross-section with elastic modulus Ef 1110 MPa. Determine the stress in the aluminum plates, the stress in the foam core, and the displacement of the column under the action of the applied force. = Note: Express tensile stresses as positive (+) and compressive stresses as negative (-). Given: • L1 L2 = = 100 mm = 1.7 m • . L3 = = 1.4 mm RIGID PLATE ALUMINUM FACE PLATE F FOAM L2 |← 41 +| |—–—– 63 L1 L3 F = 37 kN σα = σ f = |ɗ| = = number (rtol=0.01, atol=1e-05) number (rtol=0.01, atol=1e-05) number (rtol=0.01, atol=1e-05) MPa ? MPa mm ?
مقاومة المواد
Determine of the internal resistance force of each segment of the bar shown below, and the total elongation of the bar. Let: The forces acting P₁=150kN, P₂=250kN, P3=200kN, P4=50KN. Areas of the bar segments A1=1000mm, A2=2000mm, A3=1000mm. E=200Gpa -2000 mm -1000- ** -1500 P₂ 1b P3 P4 P₁ A₁ la a B A₂ b C A3 C C D
A compression load of P = 55 kips is applied to a 2 in. by 2 in. square post, as shown. Determine the normal stress σn perpendicular to plane AB and the shear stress τn⁢t parallel to plane AB. Assume α= 30°.Calculate the normal force N perpendicular to the plane AB and the shear force V parallel to plane AB. Report both answers as positive numbers.Answers: N = kips, V = kips.
When a force P of 750 N is applied to the pedal shown in the figure, find the diameter (mm) of this pin so that the resulting shear stress on the pin at C is 40 MPa.