The pole BC is supported by a pin C and by the steel wire AB. A horizontal force of 30 kN is acted on the pole at point E. Determine the required diameter of the pin at support C if the ultimate shear stresses and the safety factor are 100 MPa and 2, respectively. (Note: The pin at C is in double shear.)

The pole BC is supported by a pin C and by the steel wire AB. A horizontal force of 30 kN is acted on the pole at point E. Determine the required diameter of the pin at support C if the ultimate shear stresses and the safety factor are 100 MPa and 2, respectively. (Note: The pin at C is in double shear.)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The solid circular rod has a cross-sectional area of 350 mm². It is subjected to a uniform axial distributed loading along its length of w = 5 kN/m. Two concentrated loads also act on the rod: P = 5 kN and Q = 6 kN. Determine the normal stress in the rod at x = 1.1 m. Assume a = 0.5 m and b = 1.4 m. W A B MPa >x a Answer: 0 = i b
Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 11 mm and an allowable normal stress of 165 MPa. Pipe (2) has an outside diameter of 48 mm, a wall thickness of 7 mm, and an allowable normal stress of 75 MPa. Assume x₁ = 2.9 m, x₂ = 1.5 m, and y₁ = 3.9 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. Answer: Pmax (1) B KN
A pulley is supported by a circular pin at A. The pin has a diameter of d = 0.375 in., and each side of the pulley support bracket has a thickness of t= 0.1250 in. The average shear stress in the pin cannot exceed 40 ksi, and the bearing stress in the pulley support bracket cannot exceed 70 ksi. Determine the maximum value of Pmax that can be supported by the assembly. Pulley support bracket Answer: Pmax i ! kips %3D
The bell-crank mechanism is in equilibrium for an applied load of F₁ = 11 kN applied at A. Assume a = 300mm, b = 120mm, c = 75mm, and 0 = 40°. Pin B is in a double-shear connection and has a diameter of 23 mm. The bell crank has a thickness of 22 mm. Determine (a) the shear stress in pin B. (b) the bearing stress in the bell crank at B. Bell crank F₂ Support bracket F₁ Answers: Tpin B = i Ob = i a B MPa MPa
For the frame shown, a 4226-N load is acting on member ABD at D. If the allowable material shear stress for is 42 MPa, determine the required diameter (rounded off to the nearest 2.5 mm) of the pins at C and D. Pin C and pin D are subjected to double shear and single shear, respectively. If the thickness of member BC is 12 mm and that of member DE is 16 mm, determine the maximum bearing stress at C.
NEED ASAP THANK YOU
The uniform 713 kg bar is supported by a smooth wall at A and by a pin at B that is in double shear. Determine the diameter of the smallest pin that can be used if its working shear stress is 42 MPa. Note: Gravitational acceleration is equal to 9.81 m/s2 LAB=6 m; L1=3.6 m.
Assuming that the load P = 120 KN is carried equally by the four rivets in the figure showing the double lap connection, determine the following: (a) the shear stress in the rivets if the diameter of the rivet is 16 mm and (b) the thickness of the inner steel plate if the bearing stress is132.63 MPa.
A pulley is supported by a circular pin at A. The pin has a diameter of d = 0.375 in., and each side of the pulley support bracket has a thickness of t = 0.2500 in. The average shear stress in the pin cannot exceed 35 ksi, and the bearing stress in the pulley support bracket cannot exceed 70 ksi. Determine the maximum value of Pmax that can be supported by the assembly.
R. Q120: Determine the stress in cable shown in the figure if its diameter is 10mm. If the pins at A and C are subjected to double shear determine the shear stress in pins at A and C if their diameter is 15mm. Also, find the bearing stress in the plate in the location attached with pin A if the thickness of plate is 20mm. B. Cable sling Clevis 20 m Savel plate 50 kg 500 N 20mm
The rectangular bar is connected to the support bracket with a 19-mm-diameter pin. The bar width is w = 70 mm and the bar thickness is 15 mm. Each side of the bracket has the same dimensions as the bar. The average shear stress in the pin cannot exceed 135 MPa, the bearing stress in the bar cannot exceed 150 MPa, and the bearing stress in the bracket cannot exceed 130 MPa. Determine the maximum value of Pmax that can be supported by the structure. P Answer: Pmax i kN
Provide a complete, step by step solution: