All members of the truss shown have a cross-sectional area of 500mm2 and all pins have a diameter of 20mm2. Determine: (a)The axial stresses in members BC and DE. (b)The shear stresses in the pin at A, assuming the pin is in double shear.

Q: Part A The steel pipe in (Figure 1) has an inner diameter of 2.87 in. and an outer diameter of 3.12…

A: To find:The principal stress pointAGiven:the outer diameter of that the pipe is..The inner diameter…

Q: Problems. 1 Determine the required 1.5m cross-sectional area of t the bar BC if allowable 1.5m…

A:

Q: A thin cylinder of inner radius 500mm and thickness 10mm is subjected to an internal pressure of 5…

A:

Q: determine the developed stresses, the changes in length, and the changes in diameter for QI: The bar…

A:

Q: The rectangular bar shown is connected to a support bracket with a 27 mm diameter pin. The width of…

A:

Q: A solid circular steel cylinder S is encasedin a hollow circular aluminum tube A. The cylinderand…

A: According to Strength criterion, if a load is acting on the shaft and if the stress induced due to…

Q: The lap joint is fastened with four 3/5 in-diameter rivets. The allowable normal stress in the…

A: To Find: The maximum safe axial load P. Given :  The diameter is d=35 in. The normal stress is σ=30…

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal…

A:

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of…

A:

Q: A simplified model of a basketball hoop is shown. During a basket dunk a player hangs from the rim…

A: Given:Force applied by the player (F) = 320 lbsOutside length of the square tube (L) = 5…

Q: o solid cylindrical rod= C are welded together d as shown. The force Determine the average at the…

A:

Q: A steel pipe 120 mm external diameter and 60 mm internal diameter is subjected to an internal…

A:

Q: The structure shown below is made of 3 circular rods, each with a diameter of 1.0" and lengths as…

A: Given data  Diameter = 1 (in) Youngs modulus  Eal = 10×106 (psi) Est = 30×106(psi) EBr = 15×106…

Q: cross section at the wall is shown, with points of interest A, B, C, and D. Evaluate the potentially…

A:

Q: 3. The rigid bar ABCD of negligible weight is initially horizontal, and the steel rods attached at A…

A: Given Data The load applied at D is: P=20 kips The coefficient of thermal expansion is:…

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal…

A:

Q: 2. Determine the shear, tensile and bearing stresses on a double riveted butt joint with ¾ in. main…

A:

Q: Determine the stress developed in the Tensional Cord given that the cable's diameter is 0.6 inches…

A: Given data: Weight of the bar, W = 6000 lb. Cable diameter, d = 0.6 in. Draw a free-body diagram…

Q: The rectangular bar has a width of w = 3.50 in. and a thickness of t = 1.50 in. The normal stress on…

A:

Q: mm. When subject to pressure, the hoop stress in

A:

Q: 5. Segment AB of the bar is a tube with an outer diameter of d1 and a wall thickness of 0.125 in.…

A:

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. The…

A:

Q: A compression load of P = 50 kips is applied to a 2 in. by 2 in. square post, as shown. Determine…

A:

Q: A 100-mm diameter solid bar is applied at the surface of the bar with a torque of 5kNm and a tensile…

A: For solution refer below images.

Q: A pipe carrying steam at 3.0 MPa has an outside diameter of 450 mm and a wall thickness of 10 mm. A…

A:

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load Pat…

A:

Q: The rectangular bar is connected to the support bracket with a 15-mm-diameter pin. The bar width is…

A:

Q: An engineering machine component operating in a high temperature environment consists of a copper…

A:

Q: A simple pin-connected truss is loaded and supported as shown. The truss is constructed from three…

A:

Q: A cylindrical tank steel pressure vessel 200mm in radius and 4.0m in length, is subjected to an…

A:

Q: Two horizontal 7.5-kip forces (P) are applied to pin B of the assembly shown. A 0.8-in. diameter pin…

A: Two horizontal 7.5-kip forces are applied to pin B of the assembly shown.A 0.8-in diameter pin is…

Q: Load P shown below can be applied at any point on the steel disc (r=40mm) shown below. For this…

A: Given

Q: Determine the stresses in members LM, HM and CH. L x M N 0 P A H 40 k B 40 k C D 40 k 6 at 30 ft 180…

A:

Q: Rod (2) Rod (1)

A: Given that, Diameter of the circular rod, D=50 mm,Diameter of the pin, d=40 mm,Tensile force applied…

Q: A 28mm diameter round steel bar is 0.4m long. It is placed concentrically within a brass tube which…

A:

Q: A horizontal tension member is to be constructed of two pieces of plastic glued along the incline pq…

A:

Q: 1.What is the largest value of P (kN) that can be applied without exceeding the ollowable stress for…

A: Given : Rivet dia =  32 mm hole dia = 32+ 3 = 35 mm Allowable stress for shear = 75 mpa Allowable…

Q: 3. A circular steel cylinder of external diameter 0.2 m and internal diameter 0.1 m is shrunk onto a…

A:

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal…

A: For the Given system  P = 9 kips  Q = 5 kips R = 20 kips S = 30 kips  stress limit in (1) = 19 ksi…

Q: A thin-walled pressure vessel is made of steel with a thickness of 2 mm and an internal diameter of…

A: According to the given data P=10MPa d=300mm t=2mm We need to find The hoop stress andLongitudinal…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.