An eccentric load is applied at a point 22 mm from the geometric axis of a 60-mm-diameter rod made of a steel for which ay = 250 MPa and E= 200 GPa. Using the allowable-stress method, determine the allowable load P. Take the effective length L = 1.6 m. (Round the final answer to one decimal place.) 22 mm 60 mm diameter

Q: Which among the following is a forming process in which thickness of the metal plate is decreased by…

A: Rolling: In this handle, the workpiece within the frame of slab or plate is compressed between two…

Q: I need answers to problems 4, 5, and 6 pertaining to the print provided.

A: In the given print the length and diameter of the part is to be calculated. Which is mentioned in…

Q: Hi, -26.088 or 333.911 is INCORRECT for Ox please recheck

A:

Q: 3.00- 1.25-

A:

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: Please look at pic. Please help, I don't get part b. Thanks

A:

Q: The state of stress at a point in the machine element is shown in figure below. Determine the normal…

A:

Q: If the part was cut by this plane, what would the resulting remaining face look like?

A: Section planes in SketchUp cut a model along a plane so you may look within it without altering…

Q: I didn't understand how you fond the angle teta

A: For solution refer below images.

Q: Identify the following sectioning views (a, b, and c). a O Removed, Revolved and Removed O All…

A:

Q: e b a What is the degree of freedom of the mechanism? а. 3 O b. 0 Ос. 1 d. 4 е. 2

A: Degree of freedom is given by the following relation, F=3(l-1)-2j-h Where l=no.of link=4 j=no.of…

Q: Label all forces that act on the metal

A: A piece of metal is submerged in the liquid and one end of the metal piece is fixed with a string.…

Q: what happened with the 10 in the first equation?

A:

Q: Customary units by using the values listed for length and mass as defined values: Bending moment or…

A: As moment bending moment or torque has two variables, force and distance. So, M = F × r…… (1) The SI…

Q: Round number to three significant figures. 1.548937 x 10^7

A: For scientific notations significant digits/figures are calculated only for the coefficient or…

Q: When does a couple of moment work?

A: A couple is when a system of forces has no net force but has a net moment. A couple causes pure…

Q: where do you get the form factor (y=.337) from? Please.

A: Form factor for full depth 20° at 24 teeth can be taken from standard table. I have provided the…

Q: 2 Brass expands more than iron when heated. How would the strip look after prolonged exposure to…

A:

Q: Read the questions again. Your answer is not what I'm asking. Please redo it.  where is my FBD. Can…

A: The free-body diagram of the smaller cart is shown below.The free-body diagram of the larger cart is…

Q: A. Poppet valveu The number of degrees the camshaft turns during one four-stroke cycle. B. Blowby…

A:

Q: Write the equation that relates applied stress to local maximum stress.

A: Stress concentration factors are generally used to relate applied stress to local maximum stresses.…

Q: I need answers for problems 7, 8, and 9 pertaining to the print provided.

A: As we are entitled to answer only a single question. We’ll answer question no. 7 for you. Please…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.