Question 5 of 5View PoliciesCurrent Attempt in ProgressFor the connection shown, determine the average shear stress in the 0.75-in.-diameter bolts if the load is P = 60 kips.O 27.2 ksiO 37.5 ksiO 25.8 ksiO 21.9 ksiO 35.3 ksi

Given:Diameter of the bolts, d=0.75 inLoad acting on the loading, P=60 kipsNumber of bolts, n=5

Answered: For the connection shown, determine the…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

All the pins are in double shear, and they each have a diameter of 14 mm. The average shear stress in each pin CANNOT exceed 70 MPa. What is the max magnitude of P that the beam can support
Q1 (DÖÇ-1) In the given structure, the link BD has rectangular cross section of 18 mm × 8 mm, the diameter of the pin at C is 6 mm and the diameter of the pins at B and D is 10 mm. If the failure shear stress for the pins is 160 MPa and the failure normal stress for the link BD is 420 MPa determine the largest load P that can be applied. 35 min. D. -18 mm Note: Factor of Safety : 3.0 The pins at B and D are subjected to single shear and the pin at C is subjected to double shear 160 mm 120 mm
Two metal bars are fastened together at the bolted flange connection shown. There are 2 total bolts 12.7 mm. The flange is - connecting the two metal bars together and each bolt has diameter dbolt oriented at angle 55° with respect to longitudinal axis of the metal bars. If an axial force F = 40 kN is applied as shown, determine the overall safety factor of the bolted connection. You may assume the bolts are made out of 1020HR steel and the strength of the bolt in shear is 50% of the tensile strength of the bolt material. SF overall F = = 2.576 Ꮎ ? X 0% = F
The five-bolt connection shown must support an applied load of P = 235 kN. If the average shear stress in the bolts must be limited to 195 MPa, determine the minimum bolt diameter that may be used in the connection. Answer:d = i mm.
An axial load is applied to the rectangular cross section bar which is welded at the 57 degree angle shown. If the weld material has a failure normal stress of 160 mPa and a failure shear stress of 90 mPa, determine the required thickness if a factor of safety of 2.3 is required. Also determine the required diameter of the bolts(to the nearest mm) if the plate is face bolted to the supports. The bolt material has a failure shear stress of 175 mPa.
Solve the problems below: 1. The assembly consists of two sections of galvanized steel pipe connected together using a reducing coupling at B. The smaller pipe has an outer diameter of 20 mm and an inner diameter of 18 mm, whereas the larger pipe has an outer diameter of 25 mm and an inner diameter of 20 mm. If the pipe is tightly secured to the wall at C, determine the maximum shear stress developed in eah section of the pipe when the couple shown is applied to the handles of the wrench. B 75 N 150 mm 200 mm 75 N
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. If F₁ = 31 kips, F₂ = 11 kips, F3 = 22 kips, and F4 = 36 kips, determine the absolute value of the axial load in rod (2). F A F₂ (1) F₂ B F3 C (3) D O 16 kips O 12 kips O 7 kips O 9 kips O 22 kips
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. If F1 = 31 kips, F2 = 13 kips, F3 = 24 kips, and F4 = 37 kips, determine the absolute value of the axial load in rod (2).
5. The hanger is supported using the rectangular pin. Determine the magnitude of the allowable suspended load P if the allowable bearing stress is b,allow = 220 MPa, the allowable tensile stress is at,allow = 150 MPa, and the allowable shear stress is Tallow = 130 MPa. Take t = 6 mm, a = 5 mm and b = 25 mm. 75 mm 37.5 mm 20 mm 10 mm 37.5 mm
The rigid pipe is supported by a pin at A and an A-36 guy wire BD. The wire has a diameter of 0.27 in. Determine the load P if the end C is displaced 0.075 in. downward.
The five-bolt connection must support an applied load of P = 2600 Ib. If the average shear stress in the bolts must be limited to 27 ksi, determine the minimum bolt diameter that may be used for this connection. Answer:dmin = in.

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS