Problem 6. The A-36 steel pipe has an outer radius of 20 mm and an inner radius of 15 mm. If it fits snugly between the fixed walls before it is loaded, determine the reaction at the walls when it is subjected to the

Q: Determine the magnitude of the pin reactions at B and Cif W = 2180 Ib. 3.5' 3.5' B 2.1' W D

A: let VB is reaction at B and HC is reaction at C in horizontal direction, and HD and VD are reaction…

Q: PROBLEM 2. Two rollers of the same diameter shown are supported by an inclined plane and a vertical…

A: The Answer is below

Q: Determine the resulting internal loads on the cross section through point C in the grippers. It has…

A: Given Applied load = 20 N To find Freebody diagram Internal loading at C

Q: Determine the reaction at support B using Force method analysis. Assume support A is fixed and…

A:

Q: 1 the reactions at A and C. 3 N, A=140 N, C=180 N

A:

Q: The 2014-T6 aluminum rod has a diameter of 0.5 in. and is lightly attached to the rigid supports at…

A: Write the formula for the deformation of the rod due to the temperature change also known as the…

Q: 2 kN/m 2 m 10 kN 4 m 2 m 5m

A: Determine the point load corresponding to the point load. W=2 kN/m·5 m=10 kN So a point load of 10…

Q: The post is made from 606l-T6 aluminum and has a diameter of 50 mm. It is fixed supported at A and…

A: Given data Diameter of the post Dp= 50mm Force applied on the spring P = 40kN Spring constant K =…

Q: Determine the magnitude of the roller reaction at E.

A: Given data To determine the support reaction at E

Q: reaction at hinge F.

A: Solution : from fig. ∆ CDEtanθ = 0.31.2         θ= 14.0362 Let the force supported by the roller at…

Q: 12% of the load (3695 N) to be transferred, determine if pre-compression (a.k.a. pre-load) should be…

A:

Q: The outside diameter of the coils of a safety valve spring is 120 mm while its wire diameter is 15…

A:

Q: If the gap between C and the rigid wall at D is initially 0.15 mm, determine the support reactions…

A:

Q: Each of the two members is made from 6061-T6 aluminum and has a square cross section 1 in. * 1 in.…

A: Given data as per the question Force exerts on each member=50 lb Assume The yield strength for the…

Q: Determine the magnitude of the pin force at A. Assume W = 675 lb, a = 2.7 ft, b = 2.0 ft, r = 9 in.…

A:

Q: IF the maximum tension T that the string can sustain is 2/2W then choose the correct options. (A)…

A: Moment at end point will be zero. Correct options: A B D

Q: Q/. Determine the normal reaction at the roller A and horizontal and vertical components at pin B…

A:

Q: Determine the reactions at the pin support A and the roller B. Take F = 6.5 kN and M = 3.5 kN.m %3!…

A:

Q: The asymmetric simple truss is loaded as shown. Determine the reactions at A and D. Neglect the…

A: When an object is placed under the push or the pull, then it is possible that the shape of the…

Q: Problem Statement Based on Problem 5-74 from the textbook. The bend rod is supported at A, B, and C…

A:

Q: The asymmetric simple truss is loaded as shown. Determine the reactions at A and D. Neglect the…

A: ● To solve this problem, first we need to determine the dimensions of BC and CD using trigonometric…

Q: Problems: Determine the reaction -4 in.- 4 in. 40 lb 20 lb 2 in. CO 3 in. 3 in. 30%

A:

Q: The jib crane is pin connected at ( A) and supported by a smooth collar at ( B ). determine the…

A:

Q: The assembly consists two different sections with diameter of 40 mm and 20 mm, respectively. If the…

A:

Q: The rigid bar of negligible weight is supported as shown. The middle helical spring is made of 22 mm…

A:

Q: The structure Shown is supported by a pin at Aond roller at & Determine the suppor + reactions at…

A: The support reaction at point B is normal to the surface. The reaction at point C has two…

Q: determine the support reactions (statics)

A:

Q: Determine the reactions at the support. There are two supports: a collar that can slide along the…

A:

Q: The A-36 steel pipe has an outer radius of 20 mm and an inner radius of 15 mm. If it fits snugly…

A: For the given steel pipe connection and the load applied, the reactions at the fixed ends are as…

Q: Determine the reaction on the fixed support at point O given the load shown. Ox =  Oy =  MO =

A:

Q: Determine the reactions at the pin ( A ) and the roller ( B ) . 80N 60 5m 150 N 6. A, 4 m 5 m 3 m…

A: Consider below FBD: Here, VA = Vertical reaction at A HA = Horizontal reaction at A VB = Vertical…

Q: The member shown in Fig. 5-14a is pin connected at A and rests against a smooth support at B.…

A: Given data  To determine  The Horizontal and vertical component of reaction at A

Q: The jib crane is pin connected at (A ) and supported by a smooth collar at ( B ). determine the…

A:

Q: The pipe is stuck in the ground so that when it is pulled upward the frictional force along its…

A: From FBD,

Q: QI. Determine the normal reaction at the roller A and horizontal and vertical components at pin B…

A:

Q: Determine the reactions at the supports. 400 N/m - 3m- A = 750 N By = 600 N Bx = 450 N

A:

Q: the tension developed in any cable does not exceed 450lb. 28 2

A: to find weight of crate

Q: Determine the reactions at the pin A" and the roller E"s if (p= 500 N). 4000 N 30 11 3m 4m 4m

A:

Q: For the below assembly, if the gap between C and the rigid wall at D is initially 0.1 mm, determine…

A:

Q: The truss is supported by a pin at A and a roller at B. Determine the support reactions. 10 kN 2 m…

A:

Q: The truss is supported by a pin at A and a roller at B. Determine the suppor The truss is supported…

A:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.