Subject Directional Coupler Q1: For the symmetric directional coupler shown below, if the directivityis infinite and the forward attenuation is C=20 dB, find the transmittedpower from the source (Pt)and ( p x).1 mWB2NPtThE2mWB1200 mWC=20 dBPxΖΙ

Answered: Q1: For the symmetric directional…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.13MCQ

See similar textbooks

Similar questions

The VSWR on an 50-Ohm transmission line is 5. The distance between successive voltageminima is 80 cm while the distance from the load to the first minimum is 30 cm. What are thereflection coefficient and load impedance
The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
i need the answer quickly
4/ Which parameter is neglected or ignored in Short Transmission Lines? A. SHUNT CAPACITANCE ONLY B. SERIES CONDUCTANCE AND SHUNT CAPACITANCE C. SHUNT CONDUCTANCE AND SHUNT CAPACITANCE D. SHUNT CONDUCTANCE ONLY
Quest- A single phase 50 Hz, system supplies an inductive load of 5000 kw at power factor 0.8 lag through a line 25 km. Resistance of the line is 0.0195 2/km and inductance = 0.36 mH/km, receiving end voltage is 10 kV. A capacitor is connected across the load to get the voltage regulation of 10%. Ratio of transmission line loss with and without shunt capacitor is
The load flow data for the sample power system are given below. The voltage magnitude at bus 2 is to be maintained at 1.04 p.u.Determine the set of load flow equations at the end of first iteration by using N-R method. Impedance for sample system Bus Code Impedances line charging admittance 1-2 0.08 + j0.24 0.0 1-3 0.02 + j0.06 0.0 2-3 0.06 + j0.18 0.0 Schedule of generation and loads: Bus Code Assured Voltages Generation Load…
answer it i will rate
A three phase system with Dab Dbc one conductor per phase as shown in the figure. The conductors are stranded and spaced as shown, (Dab=Dbc=4m). The outside diameter of the phase conductor is 2cm. The GMR of the phase conductor is 0.7788 cm. The value of inductance per phase is: Select one: O a. (1.2445 * 10A-3) mH/km O b. (1.1559 * 10^-6) H/m O c. (1.4562 * 10A-6) H/m O d. (1.2945 * 10A-6) H/m O e. (1.2445 * 10A-6) H/m
5.5 kW, 1450 rpm. L-type equivalent circuit and parameters for a continuous sinusoidal phase of a star connected 3-phase ASM with line voltage 220 V and frequency 50 Hz are given as follows, ignoring core (iron) losses: R1=0.21 Ohm, R2=-0.18 Ohm, X1=X2-0.66 Ohm and Xm = 9.9 Ohm How many times the inrush current will be the rated current when the ASM is started directly? Answer options group 8.0815 2.6455 4.3763 7.1534 1.2558 6.3414 5.2280 3.7473
Each phase of a transmission line is a bundle of 4 conductors that form a square with all sides equal to d=33 cm. Each conductor is stranded and has GMR = 0.5 cm. Find GMR of the bundle to be used in inductance calculations. Express your answer in cm with 2 digits after decimal point
Thanks
Help me i need answer in 30 minutes please please please please In a 10 km long three phase conductor diameter of 2.5 mm the conductors are arranged symmetrically with a spacing of 2 m. So find per phase inductance.

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning