Q1) A V-belt drive consists of three V-belts in parallel on grooved pulleys of the same size. The angle of groove is 30° and the coefficient of friction 0.12. The cross-sectional area of each belt is 800 mm² and the permissible safe stress in the material is 3 MPa. Calculate the power that can be transmitted between two pulleys 400 mm in diameter rotating at 960 rpm.

Q1) A V-belt drive consists of three V-belts in parallel on grooved pulleys of the same size. The angle of groove is 30° and the coefficient of friction 0.12. The cross-sectional area of each belt is 800 mm² and the permissible safe stress in the material is 3 MPa. Calculate the power that can be transmitted between two pulleys 400 mm in diameter rotating at 960 rpm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4.) A flat belt makes contact with an 16 in. diameter pulley through half its circumference. If the coefficient of friction is 0.45 , and a torque of300ft−bsis to be transmitted, calculate the belt tensions. (please type answer not write by hend)
An automotive-type clutch, as shown in Figure 18.2, has inside and outside diameters of 160 and 240 mm, respectively. Clamping force is provided by nine springs,each compressed 5 mm to give a force of 900 N when the clutch is new. The moldedfriction material provides a conservatively estimated coefficient of friction of 0.40when in contact with the flywheel and pressure plate. Maximum engine torque is280 N # m.(a) What is the safety factor with respect to slippage of a brand new clutch?(b) What is the safety factor after “initial wear” has occurred?(c) How much wear of the friction material can take place before the clutch will slip (assuming no change in coefficient of friction)?
A 750 mm steel pulley transmits 120 hp at 700 rpm. The arc of contact between the belt and pulley is 152 degrees, the coefficient of friction between belt and pulley is 0.30 and the safe working stress of the belt is 2.0 MPa. Find the width of the belt used in mm if its thickness is 20 mm.
Q/The layout of a crossed leather belt drive is shown in Fig. below. The belt, transmits 7.5 kW and operates at a velocity of 13 m/s approximately. The coefficient of friction is 0.3 and the permissible tensile stress for the belt material is 1.75 N/mm2. Calculate (i) The diameters of pulleys; (ii) The length of the belt and (iii) Belt tensions on the tight and slack sides. 500 грm 1000 грm d1 d2 -1500 mm-
The axial pressure on a single disc clutch (both sides of the disc is effective) is limited to 0.12 Mpa. This is designed for a vehicle with 13kW power at a speed of 700 rpm. Assume uniform wear conditions and a friction coefficient of 0.25. If the outer dimater of the disc is 1.25 times the internal diameter, determine the dimensions of the disc lining and the axial force exerted by the springs.
A flat belt with a width of 120 mm and a thickness of 5 mm transmits power from a driving pulley with a diameter of 250 mm to a driven pulley with a diameter of 700 mm. The mass per unit length of the belt is 2.1 kg/m, and the coefficient of friction is 0.25. The input power of the belt is 60 kW at 1000 rpm. Calculate the following when the center distance is 3.5 m. (a) Maximum tensile stress of the belt(b) Axial load on each pulley
8. A cross belt arrangement has centre distance between pulleys as 1.5 m. The diameter of bigger and smaller pulleys are 'D' and 'd' respectively. The smaller pulley rotates at 1000 r.p.m. and the bigger pulley at 500 r.p.m. The flat belt is 6 mm thick and transmits 7.5 kW power at belt speed of 13 m/s approximately. The coefficient of belt friction is 0.3 and the density of belt material is 950 kg/m³. If the permissible tensile stress for the belt material is 1.75 MPa, calculate: 1. Diameters of pulleys; 2. Length and width of belt. [Ans. 500 mm, 250 mm ; 4.272 m, 90 mm]
Given: Correction factor f = 0.92, load factor k = 1.2 V-belt profile bxh = 20x12, H = 0.25 For pulleys d01 = 167 mm, d02 = 668 mm Efficiency for belt-pulley n1 = 0.91 Total efficiency for gearbox nmin = 0.95 belt-pulley system is (a) 650 mm, using the figure given according to the belt speed and belt width and using the following data; Q1. Find the forces in the stretched and loose belt arms.
A multidisk clutch is required to have a torque capacity of 300 N.m. Due to space limitations, the inner and outer diameters are specified to be 62 mm and 128 mm respectively. The coefficient of friction is 0.30 and the limiting pressure for the friction material is 900 Pa. Find the minimum number disks using uniform-wear model. Please be clear on your solution!
Note: If you don't know the solution please leave it but don't give me wrong solution. A flat open belt drive is used to transmit a power of 25kW from a motor shaft rotating at 950 rpm. The radius of the pulley of the motor shaft is 125mm while the radius of the puller of the driven shaft is 450mm. The center distance between the shafts is 2,250mm. the coefficient of friction is 0.25 and the density of the belt material is 950 kg/m^3. The belt width is 126 mm. The allowable stress is 2.6MPa. Determine the thickness of the belt.
A cross belt system gives a speed reduction of 6:1 and the centre distance between the pulleys is 2.5 m. The effective radius of the driving pulley is r, = 80 mm and it runs at the speed of 550 rpm. The grove angle of pulleys is 25°. The belt has a mass of 0.35 kg/m and the coefficient of friction of 0.3. If the tension in the belt is not to exceed 650 N, calculate the power that can be transmitted by drive.