A multi disc clutch, as illustrated below, is used to connect a four-cylinder internal combustion engine to a roll mill. The lining material is made of cast iron (Permissible pressure = 1.725 MN/m) and friction coefficient of 0.06 running in oil. If the outer diameter of the plates is limited to 200mm and the inner diameter to 100mm, compare the maximum amount of power that can be transferred at 2500 rpm by using the a) principle of uniform pressure and b) uniform rate of wear. (4C)

A multi disc clutch, as illustrated below, is used to connect a four-cylinder internal combustion engine to a roll mill. The lining material is made of cast iron (Permissible pressure = 1.725 MN/m) and friction coefficient of 0.06 running in oil. If the outer diameter of the plates is limited to 200mm and the inner diameter to 100mm, compare the maximum amount of power that can be transferred at 2500 rpm by using the a) principle of uniform pressure and b) uniform rate of wear. (4C)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The output shaft diameter is typically larger than the input shaft diameter on worm drive gearboxes. Explain why
A multiple clutch has to transmit 90kW from an engine running at 3500 rpm. Clutch lining outer diameter is 200mm and inside diameter is 160mm. Spring pressure on clutch is 170kPa and it's coefficient of friction is 0.28. a)Calculate the minimum clamping force required b) Calculate the no. of clutch plates.
Hii, please solve this..
7. Determine the minimum pressure in a plate clutch where the axial force is 1300 lb, the inside radius of contact is Ri = 2.5 in, the outside radius is Ro = 5 in. Uniform wear is assumed.
;: . L The contact surfaces in a cone clutch have an ej'fective diameter of 7‘5 i semi-angle of the cone is 15°. The coefficient of friction is 0.3. Find the torque requiy, 5 e slipping of the clutch if an axial force applied is 180 N. This clutch is employed to connect an electric motor running um_'form!y at 1 000 Epm. with, el which is initially stationary. The flywheel has a mass of 13.5 kg and its radius of gyriy, is Calculate the time required for the flywheel to attain full speed and also the energy [y, in of the clutch.
A 2hp motor is to drive a food shredder. The motor is projected to run at 1450 rpm and the required speed at the food shredder is 60 rpm. Design a double reduction drive consisting of belt and chain for this application. Please give solution and show drawing if needed
Q.1 Explain why torsional coil springs are fitted inside a clutch friction disc. Q.2 Study examples of competition sintered or 'paddle' type clutches. Most of them do not have torsional springs fitted to the friction disc/plate. Suggest why springs are not fitted to these types of clutches.
Which clutch would you use to connect two spindles with a 250 angle between them? Why you chose this clutch, in terms of uniform moment transmission? Explain that it must meet the requirements.
A multidisk clutch is required to have a torque capacity of 300 N.m. Due to space limitations, the inner and outer diameters are specified to be 62 mm and 128 mm respectively. The coefficient of friction is 0.30 and the limiting pressure for the friction material is 900 Pa. Find the minimum number disks using uniform-wear model. Please be clear on your solution!
Note: If you don't know the solution please leave it but don't give me wrong solution. A flat open belt drive is used to transmit a power of 25kW from a motor shaft rotating at 950 rpm. The radius of the pulley of the motor shaft is 125mm while the radius of the puller of the driven shaft is 450mm. The center distance between the shafts is 2,250mm. the coefficient of friction is 0.25 and the density of the belt material is 950 kg/m^3. The belt width is 126 mm. The allowable stress is 2.6MPa. Determine the thickness of the belt.
In a transmission system 25 ° spur gears are used and the number of teeth on each gear is Np=25 and NG=50. Load is applied at the highest point of single-tooth contact. Power source is electric motor and the transmission system drives uniformly loaded conveyors. The overload factor, Ko is:
I want the answer for all of these questions