Find the power transmitted by a belt running over a pulley of 500mm diameter at 300 rpm.The coefficient of friction between the belt and the pulley is 0.26, angle of lap 160 degree and the max. tension in the belt is 2400 N.

Find the power transmitted by a belt running over a pulley of 500mm diameter at 300 rpm.The coefficient of friction between the belt and the pulley is 0.26, angle of lap 160 degree and the max. tension in the belt is 2400 N.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A multiple V-belt drive is required to transmit 4 kW. The smaller pulley of the system is150 mm diameter, rotates at 200 rev/min, and has an angle of lap angle of 135°. Thegrove angle is 40° and the coefficient of friction between the belt and the pulleys is 0·3.If the maximum tension in any one belt is limited to 800 N, calculate:(a) The number of belts required. (b) The minimum tension in any one belt. (c) The required pre-tensioning of the belt. The centre-to-centre distance between the pulleys is 2 m.(d) Determine to the nearest mm, the required size for the larger pulley.(e) Find the approximate length of the belt
solve show solution
Determine the percentage increase in power capacity made possible in changing over from flat belt drive to V-belt drive. The diameter of pulley is same as the pitch diameter of grooved pulley. The pulley rotates at the same speed as the grooved pulley. The coefficient friction for the grooved and flat belt is same and is 0.3. The V-belt pulley groove angle is 60°. The belts are of the same material and have same cross-sectional area. In each case, The angle of warp is 150°.
A V-belt drives a pulley at a speed of 1440 m/min. The coefficient of friction between belt and pulley is 0.3, semi V-groove angle is 22.5 degree and angle of contact of belt with the pulley is 160 degree. Ifthe mass of the belt is 0.45 kg/m and if permissible pull in the belt is 800 N. Calculate the power.(Consider the centrifugal tension in the belt.)
None
Prob # 9. Find the horsepower transmitted by a pair of friction wheels, the diameter of driving wheel is 10 inches, and it revolves at 200 rpm. The width of the wheel is 2 inches. The force per inch width of face is 150 pound and the coefficient of friction is 0.20. a. 96 hp b. 23 hp c. 1.2 hp d. 1.6 hp
Plz attempt if you know the answer otherwise skip to another expert. A flat belt is required to transmit 30 kW from a pulley of 1.5 m effective diameter running at 300 rpm. The angle of contact is spread over 11/24 of the circumference. The coefficient of friction between the belt and pulley surface is 0.3. Determine taking centrifugal tension in to account, width of the belt required. It is given that the belt thickness is 9.5 mm, density of belt material is 100 kg / (m ^ 3) and the permissible working stress is 2.5 MPa.
In an open flat belt drive, a pulley of 800 mm diameter runs at 300 r.p.m. The coefficient of friction between the belt and the pulley is 0.25, the angle of lap is 170° and the maximum tension in the belt is 2000 N. The power transmitted is: 10.5 kW 9.4 kW 8.9 kW 7.6 kW None of the mentioned 13.1 kW
A flat belt passes over two idler pulleys and under a rotating drumof diameter 8 in. The axle of the drum is free to move vertically ina slot, and a spring keeps the drum in contact with the belt. Whatis the minimum force which should be exerted by the spring if slippageis not to occur when a 30-lb · ft torque is applied to the drum? Thecoefficient of static friction between belt and drum is 0.30 and theangle of contact is 180 degrees.
The tension in a pulley belt is 300 N when stationary. The smaller pulley has a diameterof 300 mm and a speed of 1420 rev/min. The coefficient of friction between the belt andthe pulley is 0·4 and the angle of lap is 160°.(1) Calculate the tension in each side of the belt at operating speed. (2) Determine the power transmitted when the belt is on the point of slipping. If the pulley system uses a flat belt of CSA 500 mm² and density 1300 kg/m3, determine:(3) The power transmitted, when the mass of the belt is taken into consideration.
A multiple vee-belt drive is required to transmit 4 kW. The smaller pulley has of the systemhas a diameter 150 mm and rotates at 200 rev/min. The grove angle is 40° and thecoefficient of friction between the belt and pulley is 0·3.(a) If the maximum tension in any one belt is limited to 800 N and the angle of lap is135°, determine the number of belts required. (b) Determine also, the initial pre-tension required in the belt.
Find the power transmitted by a belt running over a pulley of 600 mm diameter at200 r.p.m. The coefficient of friction between the belt and the pulley is 0.25,angle of lap 160° and maximum tension in the belt is 2500 N.