pulleys are 300 and 850 mm, respectively, and the center distance is 2 m. The belt has a width of 200 mm, thickness of 10 mm, speed of 20 m/s, and coefficient of friction of 0.40. For a safety factor of 2.0 for static loading, determine the following: A flat belt drive is used to transfer 100 kW of power. The diameters of the driving and driven a. The contact angles and belt length for an open configuration b. The loads for each pulley on the axis 02 D2 01 D. 02

pulleys are 300 and 850 mm, respectively, and the center distance is 2 m. The belt has a width of 200 mm, thickness of 10 mm, speed of 20 m/s, and coefficient of friction of 0.40. For a safety factor of 2.0 for static loading, determine the following: A flat belt drive is used to transfer 100 kW of power. The diameters of the driving and driven a. The contact angles and belt length for an open configuration b. The loads for each pulley on the axis 02 D2 01 D. 02

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

DD=25
A multiplate disc clutch consist of a branz plate to transmit 10 kw at 1000 rpm di= 90 mm do= 160 mm friction coefficient =0.18 and the pressure is 0.3. find the number of contact surfaces.
The factor of safety against slipping in the friction clutch = 1.3; coefficient of friction=0.4;working speed= 600 rpm; friction surface number= 2; required closing force= 712 N, clutch outerIf diameter = 300 mm, clutch inner diameter = 120 mm, how much power is transmitted?
b) Design a self-aligning ball bearing with basic dynamic load rating of 69.5 KN to be used in the automobile industry to carry a thrust load of 1184 N. The expected life of the bearing is 5201 hours at 628 rpm. Take k=3 for all types of ball bearings. Take the value of the shock load factor as 1.7 and radial and axial load factors are 1.4 and 2.2 respectively, the rotational factor is 1. Calculate: i) Expected life of bearings in millions of revolutions ii) Design equivalent dynamic load in N iii) Basic equivalent dynamic load in N iv) Radial load acting on the bearing in N
For the given details, design a self-aligning ball bearing to be used in a textile machinery to carry a combined radial load of 6139 N and thrust load of 1153 N. The expected life of the bearing is 150 millions of revolutions at 734 rpm. Take k=p=3 for all types of ball bearings. Assume uniform steady state load and take the corresponding factor as 1.1. Radial and axial load factors are 0.65 and 1.2 respectively, rotational speed factor is 1. Note: Please upload your handwritten working/solution to the link provided. Dynamic load on the bearing in N Dynamic equivalent load considering steady state load factor in N Dynamic load carrying capacity in N -
A flat belt is required to transmit 35 kw from a pulley of 1.5 m effective diameter running at 300 rpm. The angle of contact spread over 11/24 of the circumference and the coefficient of friction between pulley and belt 0.3. Determine width of belt required. It is given that the belt thickness is 10mm, density of its material is 1.1Mg/m and the related permissible working stress is 2.5 Mpa.
The three flat blocks are positioned on the 30° incline as shown in Figure WDG – 3F, and a force P parallel to the incline is applied to the middle block. The upper block is pre vented from moving by a wire which attaches it to the fixed support. The coefficient of static friction for each of the three pairs of mating surfaces is shown. 1. Calculate the normal force (N) acting between 50-kg and 40-kg blocks (ANSWER: 680) and the maximum frictional resistance (N) on the surface between the 30-kg and 50-kg blocks (ANSWER: 76.5) 2. Calculate the maximum frictional resistance (N) on the surface between the 40-kg block and inclined surface (ANSWER: 459) and also determine the maximum value which P (in N) may have before any slipping takes place (ANSWER: 94).
A cone clutch has D = 16 in, d = 14 in, a cone length of 3 in, and a coefficient of friction of 0.35. A torque of 3 kip-in is to be transmitted. For this requirement, estimate the actuating force and pressure by both models.
A 55-hp four-cylinder internal combustion engine is used to drive a medium-shock brick-making machine under a schedule of two shifts per day. The drive consists of two 25-in sheaves, with a sheave speed of 425 rev/min. A value of Ks = 1.5 and a design factor of 1.0 applies. Determine the number of D360 V-belts needed, calculate the factor of safety, and estimate the life in hours. The number of D360 V-belts needed is The factor of safety, nfs, is belts. and the life of the belts is hours.
A single-threaded power screw with square threads pushes against a load of 3,276 N at a speed of 14 mm/s. The screw has a mean thread diameter of 18 mm and a pitch of 2 mm. The frictional coefficient of the threads is 0.33, and collar friction is negligible. How much torque must be applied to drive the screw against the applied load in units of newton meters? A double frictiona
Derivation of the relationship between tensile strength, contact angle and friction coefficient of a V-type belt
A narrow V-belt (wedge belt) transmits power from an internal combustion engine operating at 700 rpm to the shaft of a dough mixer (medium duty) operating at 50 rpm. The internal combustion engine develops a nominal power of 50 kW and the dough mixer operates for no more than 8 hours per day. Which of the following belts can be used for this application? Hint: First determine the design load by using an appropriate service factor from page F12 in Appendix H in the Design Manual. SPC only SPB or SPC SPA or SPB SPB only