Design the elliptical cross-section of a belt pulley arm near the hub for the following specifications: The mean pulley diameter is 300 mm and the number of pulley arms are 4. The elliptical section has major axis twice the minor axis length. The tight and slack sides tension in the belt are 600 N and 200 N respectively. Assume half number of arms transmit torque at any time and the load factor of 1.75 to account for dynamic effects on the pulley while transmitting torque. The permissible tensile stress for cast iron pulley material is 15 MPa. The pulley hub diameter is 60 mm.

Design the elliptical cross-section of a belt pulley arm near the hub for the following specifications: The mean pulley diameter is 300 mm and the number of pulley arms are 4. The elliptical section has major axis twice the minor axis length. The tight and slack sides tension in the belt are 600 N and 200 N respectively. Assume half number of arms transmit torque at any time and the load factor of 1.75 to account for dynamic effects on the pulley while transmitting torque. The permissible tensile stress for cast iron pulley material is 15 MPa. The pulley hub diameter is 60 mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please answer correctly. Show all the steps
Below question is from machine design. Please solve asap. You have to select bearings which are used to support a shaft, bearings are mounted at each end of shaft and 1.20 metre apart. A 600 mm diameter pulley is mounted at a distance of 300 mm to the right of left hand bearing and this drives a pulley directly below it with the help of belt having maximum tension of 2.25 kN. Another pulley 400 mm diameter is placed 200 mm to the left of right hand bearing and is driven with the help of electric motor and belt, which is placed horizontally to the right. The angle of contact for both pulleys is 180º and .Allowing working stress of shaft depends on the material you have selected for the shaft. Select the type of bearing mounted on both ends of shaft (either ball or roller bearing type and also elaborate the scenario for the selection of bearing).The Reliability Factor for Bearing may vary from 92% till 96%
A single-threaded power screw of ACME form is to lift a load of 585 kg at 50 rpm. The mean diameter is 20 mm and pitch is 5 mm. Assume that the friction on threads is 0.1. Determine the torque needed to turn the screw in N-m without considering collar torque.
None
Consider a crank rocker mechanism with L1 = 90 mm, L2 = 180 mm, and L3 = 270 mm. The design transmission angle of the mechanism is 45o135o. Determine the range of values of L0.
Design a helical extension spring to hold the roller follower against the cam as shown in Figure 1. The maximum extension of spring (ymax = 8.3 mm), the dynamic load varies from 250 N at the low position and 400 N at the high position . The diameter of the circular cam is 200 mm rotates off center with an eccentricity of 25 mm and operates the roller follower that is carried by the arm. The speed of the cam is 200 rpm. Design choices, (C= 10 ), shear modulus G= 80 GPa , A227 as a material for the spring, Wire endurance limit Sew = 310 MPa, factor of safety for spring body is 1.5. The spring ends are standard. a. Check the initial tension in the spring and compart it with minimum load. b. Determine the physical parameters of the spring. c. Check the surging of spring. 200 mm -100 mm- - - Spring 25 mm ww
A narrow V-belt (wedge belt) transmits power from an internal combustion engine operating at 700 rpm to the shaft of a dough mixer (medium duty) operating at 50 rpm. The internal combustion engine develops a nominal power of 50 kW and the dough mixer operates for no more than 8 hours per day. Which of the following belts can be used for this application? Hint: First determine the design load by using an appropriate service factor from page F12 in Appendix H in the Design Manual. SPC only SPB or SPC SPA or SPB SPB only
The pedal system shown in the figure is exerted by both an up and down mechanism. These forces are Fmax=350*SN/10 N, Fmin=-150*SN/10 N. It is desired that h/b = 5 seen in the figure. This piece is AISI 1040 and has a maximum tensile stress of 670Mpa and a yield stress of 540Mpa. Known weakening factors are known as kb=ky=kd=0.8. The notch factor for all stresses is assumed to be Kç=1.5. It is desired to last up to its minimum indefinite life at the cross-section measurement point (bxh) shown in the figure. According to Goodman theory, what should be the minimum size (b and h value) of this section in order to meet this condition. SN=89
please I want quick answer
STATİC I need the answer within 1 hour. Thanks Rod AB is secured from point B with a cable and from point A with a smooth, up and down movable collar. Calculate the tensile strength generated in the BC cable. ? = {−??} N direction is -z a(m)=15.75 , b(m)=13.5 , c(m)=8.55 d(m)=3.75 F(N)=61.5
A 2hp motor is to drive a food shredder. The motor is projected to run at 1450 rpm and the required speed at the food shredder is 60 rpm. Design a double reduction drive consisting of belt and chain for this application. Please give solution and show drawing if needed
please slove both