Two pulleys with diameters (450 mm) and (200 mm), centre distance (1.95 m). if we use cross belt drive. Determine the length of flat belt, and the contact angle between belt and smaller pulley. Also determine the horse power. If the large pulley turns with speed (200 rpm) and the tension force in tight side is (1000 N), coefficient of friction u=0.25

Two pulleys with diameters (450 mm) and (200 mm), centre distance (1.95 m). if we use cross belt drive. Determine the length of flat belt, and the contact angle between belt and smaller pulley. Also determine the horse power. If the large pulley turns with speed (200 rpm) and the tension force in tight side is (1000 N), coefficient of friction u=0.25

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 150 lb man stands on a 60 lb bar to which the cable is tied at B. The cable passes over two fixed pegs with coefficient of frictions as indicated. You may treat the cable the same as you would treat a flexible flat belt. assume the normal force exerted by the man in the bar acts downward through point A. Find the smallest force the man can exert on the cable if the bar is to remain horizontal.
100 mm 200 mm GIVEN: Coefficient of static friction at A = 0.4 Collar at B is smooth and exerts horizontal force on pipe Mass of bracket is negligible ASK What is minimum distance x so bracket can support cylinder at any mass without slipping?
The figure shows a system with a block m1 attached to a simple square thread screw with a mean diameter of 10 mm, a pitch of 3 mm and whose coefficient of static friction on the thread is 0.35. Block m1 is attached to block m2 by a rope, each of blocks m1 and m2 have a mass of 4 kg.Block m2 is in turn attached to a 15-kg block W by another rope, which passes over a static drum where the coefficient of static friction is 0.20. Determine the required Moment M that must be applied to the screw to start lifting block W. The coefficient of static friction between the surface and blocks m1 and m2 is 0.25. Need free body diagrams
8. Answer the following questions about the exercise of Box A (massmA=50kg) and Box B (mB=10kg) located on the slope as shown in Figure 7. Between slope and box A, the coefficient of static friction is uk, and the angle of slope is 10 degrees, although box A and B are connected in a solid line and ignore the mass of the pulley.1)What is the maximum friction (kgf) between Box A and Slope for us=0.4 and Uk=0.15?2)What is the maximum friction between Box A and the slope (kgf) for us=0.3 and UK=0.15?3)us=0.3 and Uk=0.15 What is the tension in kgf?4)us=0.3 and uk=0.15 when box B goes down 2m, calculate the size (m/s) of the speed of box A and box B using the modified energy supply law.
A V-belt drives a pulley at a speed of 1440 m/min. The coefficient of friction between belt and pulley is 0.3, semi V-groove angle is 22.5 degree and angle of contact of belt with the pulley is 160 degree. Ifthe mass of the belt is 0.45 kg/m and if permissible pull in the belt is 800 N. Calculate the power.(Consider the centrifugal tension in the belt.)
The coefficient of static friction under the block a and b are the same. If the block is in the verge of sliding, find the tension at each chord. Assume that the pulley is frictionless.Recall [from Physics]:?? = ???Where:?? - is the frictional force?? - is the normal force? -coefficient of static frictiona. Determine the tensile force (lb) on the cable 1.b. Determine the tensile force (lb) on the cable 2. Plsss show complete handwritten solution. Thanksss!!
10 kN FIGURE P5-36 In Problem 5-36, if a force P= 400 N is required to resist the 10-kN force. determine the coefficient of static friction between the rope and the shafts. 5-37
A flat belt passes over two idler pulleys and under a rotating drumof diameter 8 in. The axle of the drum is free to move vertically ina slot, and a spring keeps the drum in contact with the belt. Whatis the minimum force which should be exerted by the spring if slippageis not to occur when a 30-lb · ft torque is applied to the drum? Thecoefficient of static friction between belt and drum is 0.30 and theangle of contact is 180 degrees.