oughly position of the automobile jack shown in the figure is a square screw with a single blade at both ends. ABC is controlled by a bolt (right-hand threaded in A, left-handed in C). square of the bolt screw has a pitch of 2.5 mm and an average diameter of 9 mm. between the bolt and the jack limbs The coefficient of static friction is 0.15, taking into account t

Q: Two blocks are connected by a ngid strut (with negligible weight) attached to each block with…

A: FBD is drawn for both the masses A & B. fs=μN Answer: WA = 736.98 kN

Q: Block A has a mass of m = 58.0 kg and rests on a flat surface. (Figure 3)The coefficient of static…

A: When a body is in static equilibrium, the net external force acting on the body is equal to zero. To…

Q: Determine the maximum incline e [degrees] that the car can drive up if it has front-wheel drive.…

A: Disclaimer:“Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: M1 M2 R friction The figure above illustrates a system comprising a rigid support structure having a…

A:

Q: Solve each of the following problems indicated below. Present your complete-detail solution…

A: Write the given value using suitable variables. Here Tmax signifies cord maximum tension and μs…

Q: For the drum brake shown in the following figure, there is an inner rim diameter of 280 mm and…

A:

Q: The figure shows 3 blocks. Block C hangs from a rope which passes through a fixed cylinder and is…

A: The maximum mass of the block C is mc=54kg The maximum mass of the block B is mb=mb+8=70kg

Q: As shown in the figure below, three boxes are placed on an incline. The boxes are initially in…

A: Given data as per the question Mass of block A =20 lb Mass of block B= 40 lb Mass of block C = 30 lb…

Q: following figure shows a belt braking system operating on a brake drum for a lifting mechanism. It…

A:

Q: 20 kg ladder AB up a wall by applying the horizontal force P (Figure 4). Determine the height, h…

A:

Q: Form the figure shown, a flexible belt placed around a rotating drum of 4-inch radius acts as a…

A:

Q: The device shown is used for coarse adjustment of the height of an experimental apparatus without a…

A: Coefficient of friction is μs=0.32. The equilibrium condition is obtained under the following…

Q: A block brake is used to stop a drum of 400 mm diameter. The contact angle is 90°. The coefficient…

A: Given:Drum diameter, d=400 mmcontact angle, α=90ocoefficient of friction, μ=0.3force, F=350 N

Q: Form the figure shown, a flexible belt placed around a rotating drum of 4-inch radius acts as a…

A: Given data as per the question Radius of drum=4 inchμ=0.7Braking Torque=400 lb in

Q: Determine the force T that will produce impending motion upward of the 500-lb weight in Figure…

A:

Q: IV. The belt drive is shown in the following Figure, please draw up the friction direction on the…

A:

Q: A differential band brake is shown in the figure. The diameter of the drum is 800 mm. The…

A: Diameter of the drum,(D)=800 mm. Coefficient of friction,(μ)=0.3 The angle of embrace,(θ)=240o…

Q: 4.) A flat belt makes contact with an 18 in. diameter pulley through half its circumference. If the…

A:

Q: A power screw has single square threads. It has a major diameter of 36 mm and a pitch of 6 mm. The…

A:

Q: Provide a complete and elaborate solution. Show step by step solution  Consider the figure below.…

A:

Q: For the figure shown, two blocks are connected by a uniform solid rod attached to each block with…

A: Given data :- coefficient of friction (μ)=0.65 weight of block B (WB) =2700N To find:- Minimum…

Q: The disc clutch has a pair of mating friction surfaces, with an outer diameter of 350 mm and an…

A: Given data:- outer diameter=350 mm inner diameter =250 mm The average value of the coefficient of…

Q: The crate has a weight of 490 lb and a center of gravity at G rests on the floor for which the…

A: Given data: -  The weight of the crate is W = 490 lb. The coefficient of static friction is μ =…

Q: A 5/8-11 unc x1.75 long grade 8 bolt clamps an assembly as shown. A total load (P)of 11500 lbs is…

A:

Q: Determine diameter of hand-wheel or length of handle, assuming that maximum force exerted by a man…

A: Given, Force exerted by a man, F=150lbf Force need to be applied, P=6000lbfCorfficient of…

Q: The block-type parking brake shown in the figure has a width of 49 mm and an average friction…

A:

Q: For the same question, the Impeller hub will be pressed onto the taper shaft with the Nut. How much…

A: given data; ⇒engine power(P)=27kw                        =27*103w⇒speed (n)=1684rpm⇒conical…

Q: A pulley system uses four v-section belts each with a cross-sectional area of 700mm 2, an included…

A: The maximum force (tension) in the belt can be given as -  T1 = 3×Centrifugal force500 =…

Q: In the figure, a climber with a weight of 390 N is held by a belay rope connected to her climbing…

A: Given Data The weight of the climber is: w=390 N The angle at the toe is: θ=45° The angle at the…

Q: Problem -02 Dry FrictionKnowing that a couple of magnitude 30 N m is required to start the vertical…

A:

Q: The wheel has a weight of 20 lb and a radius of gyration of kg = 0.75 ft. If the coefficients of…

A:

Q: The following lead screw and saddle arrangement is used to lift a load of 550 kg.   The square…

A: m = 550 Kg W = 550 × 9.81 = 5395.5 N Pitch P = 3mm Diameter d = 15 mm Coefficient of friction µ =0.2…

Q: A flat belt makes contact with an 16 in. diameter pulley through half its circumference. If the…

A: Given data:- Diameter of pulley =16 in Angle of contact θ =π the coefficient of friction μ = 0.45…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.