A narrow V-belt (wedge belt) transmits power from an internal combustion engine operating at 700 rpm to the shaft of a dough mixer (medium duty) operating at 50 rpm. The internal combustion engine develops a nominal power of 50 kW and the dough mixer operates for no more than 8 hours per day. Which of the following belts can be used for this application? Hint: First determine the design load by using an appropriate service factor from page F12 in Appendix H in the Design Manual. SPC only O SPB or SPC SPA or SPB SPB only

A narrow V-belt (wedge belt) transmits power from an internal combustion engine operating at 700 rpm to the shaft of a dough mixer (medium duty) operating at 50 rpm. The internal combustion engine develops a nominal power of 50 kW and the dough mixer operates for no more than 8 hours per day. Which of the following belts can be used for this application? Hint: First determine the design load by using an appropriate service factor from page F12 in Appendix H in the Design Manual. SPC only O SPB or SPC SPA or SPB SPB only

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For the Finishing Mill of a hot strip mill, the input shaft of several different gearboxes are each driven by a DC motor of 10,500 HP operating at 125 RPM. For your ASSIGNED gearbox only, you are required to analyze the gearbox capabilities by doing thefollowing: 1. Calculate the maximum motor torque2. calculate the force transmitted by the gearing.3. Using statics, calculate the equivalent radial load at the bearings for BOTH the pinion shaft and the gear shaft. (Four bearings total; two per shaft). Include FBDs of the shafts.4. Research the load capacities for the bearings.(Hint: the bearing manufacturer is most likely Timken / Torrington).5. Calculate the expected bearing life for each bearing.6. Calculate the safety factor for both the bending strength and the pitting resistance for the pinion shaft AND the gear shaft gear teeth based on the transmitted load and the gear material(s).7. Draw the shear, bending moment, and torque diagrams for the GEAR SHAFT ONLY.8. Calculate the…
Design a chain drive to run a blower at 600 rpm. the power to the blower is available from a 8kw motor at 1500 rpm. the centre distance is to be kept at 800 mm.
A self-aligning ball bearing used in the car manufacturing industry has a basic dynamic load rating of 48899 N. The desired life of the bearing is 2303 millions of revolutions. Calculate the equivalent dynamic load on the bearing in N. For ball bearing, the value of k is 3.
A food product with 80% moisture content in a 7 cm diameter can wants to be frozen. product density is 1000 kg / m³ thermal conductivity is 1.0 W / (m K) and initial freezing temperature is -2.25 degrees Celsius after 8 hours in freezing medium -35 degrees Celsius Temperature to -10 degrees Celsius estimate convection heat transfer coefficient freezing medium assume the can as an infinite cylinder h =
Two single-row 02-series angular contact ball bearings with inner ring rotation are to be selected by a student for her Capstone project from Table 11-2 to support a radial load of 3.5 kN and axial load of 1.25 kN. The desired total machine reliability is 95%. The desired life of the bearings is 1 year of continuous operation in a machine operating at 900 rpm with light to moderate impact. Use the "manufacturer 2" Weibull values from Shigley Table 11-6 and equivalent radial load factors from Table 11-1. Fully specify the smallest bore size for these conditions.
Consider a crank rocker mechanism with L1 = 90 mm, L2 = 180 mm, and L3 = 270 mm. The design transmission angle of the mechanism is 45o135o. Determine the range of values of L0.
A shaft transmitting 10kW of power at 750 rpm, has a diameter of 20mm. Design a square key made of steel for: factor of safety (n) =2. Use preferred sizes.
The following data are available for a belt conveyor design: 1. Conveyor capacity: = 1300 t/h; 2. Belt speed = 1.5 m/sec; 3. Conveyor height = 15 m; 4. Conveyor length = 175 m; 5. Mass of a set of idlers = 15 kg; 6. Idler spacing = 1.2 m; 7. Load due to belt = 25 kg/m; 8. Inclination angle of the conveyor = 10 deg.; 9. Coefficient of friction = 0.05; 10. Start-up factor = 1.5; 11. Drive efficiency = 0.90; 12. Friction factor = 12; and 13. Breaking strength loss factor = 0.80 Determine the following: (1) Belt tension, (2) Load due to idlers, (3) Minimum motor power; (4) Acceleration of the conveyor belt, and the (5) Belt breaking strength.
spring is to be inserted with an initial compression to produce a force equal to 125 N between the right-hand end of the lever and the stop. When the maximum force at A reaches to a value of 200 N, the end of the lever moves downward by 25 mm. assuming a spring index 8 determine the following parameters: 1. Spring rate 2. Size of the wire 3. Outside diameter of the spring 4. Number of active coils, and 5. Free length, assuming squared and ground ends Note: the allowable shear stress may be taken as 420 MPa, and G = 80 GPa. Hint: Ans. 0.33 N/mm: 3.4 mm; 27.2 mm; 77 mm - 200 mm - 200 mm Lever Stop -Spring
show all steps and solution
A multi plate friction clutch is used to transmit the power from the engine to a rotor which has a mass of 152 kg and a radius of gyration of 0.34 m. The inner and outer radius of the clutch disc is 0.055 m and 0.217 m respectively. The clutch plate has 4 contact surfaces (n = 4) and the axial thrust is 379 N. The flywheel of the engine rotates constantly at 1,106 rpm. Calculate the time required to accelerate the rotor from rest if the clutch is suddenly engaged. Take u = 0.42. Assume uniform wear in clutch.
A shaft transmitting 10kW of power at 750 rpm, has a diameter of 20mm. Designa square key made of steel for: factor of safety (n) =2. Use preferred sizes.