Q4/A single V belt is to be selected to deliver engine power to the wheel-drive transmission of a riding tractor. A 5-hp single-cylinder engine is used. At most, 60 percent of this power is transmitted to the belt. The driving sheave has a diameter of 6.2 in, the driven, 12.0 in. The belt selected should be as close to a 92-in pitch length as possible. The engine speed is governor-controlled to a maximum of 3100 rev/min. Select a satisfactory belt and assess the factor of safety and the belt life in passes.

Q4/A single V belt is to be selected to deliver engine power to the wheel-drive transmission of a riding tractor. A 5-hp single-cylinder engine is used. At most, 60 percent of this power is transmitted to the belt. The driving sheave has a diameter of 6.2 in, the driven, 12.0 in. The belt selected should be as close to a 92-in pitch length as possible. The engine speed is governor-controlled to a maximum of 3100 rev/min. Select a satisfactory belt and assess the factor of safety and the belt life in passes.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A belt conveyor transports 18 tonnes per hr at 20°. Calculate the total length to be sufficient to give 33.5 m horizontal center-to-center pulley distance. 1750-rpm motor, V-belt drive to helical gear speed reducer. Belt speed, 61 m/min. Discharge over tail pulley.
A belt conveyor transports 18 tonnes per hr at 20°. Determine the speed reducer power factor to lift the load vertically up sufficient to give 33.5 m horizontal center-to-center pulley distance. 1750-rpm motor, plain chain drive to helical gear speed reducer. Belt speed, 61 m/min. Discharge over tail pulley. No tripper.
Q6:- A pinion having 20 involute teeth of module 6 mm rotates at 200 rpm and transmits 1.5 kW to a gear wheel having 50 teeth. The addendum on both the wheels is 0.25 of the circular pitch. The angle of obliquity is 20°. Find (a) the contact ratio and (b) the maximum and minimum force between teeth.
Design a crank-rocker mechanism with a time ratio of Q = 1.34, throw angle of (θ4)MAX= 85°, and time per cycle of t = 4.8s. Specify the link lengths and crank speed
A shaft rotating at constant speed is subjected to variable load. The bearings supporting the shaftare subjected to stationary equivalent radial load of 3 kN for 10 per cent of time, 2 kN for 20 percent of time, 1 kN for 30 per cent of time and no load for remaining time of cycle. If the total lifeexpected for the bearing is 20 × 106revolutions at 95 per cent reliability, calculate dynamic loadrating of the ball bearing.
Design a chain drive to run a blower at 600 rpm. the power to the blower is available from a 8kw motor at 1500 rpm. the centre distance is to be kept at 800 mm.
A pinion of 20° involute teeth has a minimum number of teeth of 13 in order to avoid interference. If the pinion is to be used for a drive having velocity ration of 5, find the standard ratio of its module to addendum.
A conveyor is used to drive the inertial load of 0.02 kg m² in the required speed range with a brushless DC motor and a gearhead having reduction ratio of 15:1 as shown in the figure below. The belt speed is V=1 m/s and the roller diameter is D=0.1 m. Choose the correct statement. Load Motor Right Angle Gearhead O The moment of inertia of the load referred to the motor shaft is 0.00133 kg m² O The moment of inertia of the load referred to the motor shaft is 0.0133 kg m² O The rotation speed of the motor shaft is 1665 RPM O The rotation speed of the gear shaft is 100 RPM O The rotation speed of the motor shaft is 2865 RPM.
Figure Q4 shows a Mach trim system from a 737-800. It consists of a hydraulic motor driving gear A which drives gear B. Gear B is directly connected to the horizontal stabiliser via rack and pinion as depicted below. Gear A has a mass of 6kg, a radius of gyration of KGA = 0.1235m and an angular acceleration of 20kg, and a radius of gyration of Ö = 0.2t rad/s². Gear B has a mass of m = m = = 0.5341m. If the system starts from rest, determine the following when t = 3s: KGb a) The velocity of the gear rack. b) The distance the rack has travelled. c) If there is a contact force between the rack and gear B of 50N, determine the contact force between Gear A and B. d) The applied torque from the hydraulic motor. 100mm 500mm B 200mm Figure Q4-Mach Trim System tastes ins
A 55-hp four-cylinder internal combustion engine is used to drive a medium-shock brick-making machine under a schedule of two shifts per day. The drive consists of two 25-in sheaves, with a sheave speed of 425 rev/min. A value of Ks = 1.5 and a design factor of 1.0 applies. Determine the number of D360 V-belts needed, calculate the factor of safety, and estimate the life in hours. The number of D360 V-belts needed is The factor of safety, nfs, is belts. and the life of the belts is hours.
A 10 pitch pinion with 20 teeth mates with a gear having 80 teeth The pinion rotates at 3,000 RPM. The gear pair is to be installed in a rectangular housing where a minimum of 0.20 in clearance botween the gears and housing is requirod. Specify the dimensions X and Y as shown in tho figure below Note: This question requires a file attachinent, which can be pdf, ipeg. word, excol or power point. Show all your calculations. Handwritten calculations are acceptable. 0.20 in 0.20 In 0.20 in GEAR PINION N, 20
Design a helical extension spring to hold the roller follower against the cam as shown in Figure 1. The maximum extension of spring (ymax = 8.3 mm), the dynamic load varies from 250 N at the low position and 400 N at the high position . The diameter of the circular cam is 200 mm rotates off center with an eccentricity of 25 mm and operates the roller follower that is carried by the arm. The speed of the cam is 200 rpm. Design choices, (C= 10 ), shear modulus G= 80 GPa , A227 as a material for the spring, Wire endurance limit Sew = 310 MPa, factor of safety for spring body is 1.5. The spring ends are standard. a. Check the initial tension in the spring and compart it with minimum load. b. Determine the physical parameters of the spring. c. Check the surging of spring. 200 mm -100 mm- - - Spring 25 mm ww