A mini motorcycle is driven by a combustion engine with mechanical transmission. The 12Hp motor spins at a speed of 1150 rpm. The motorcycle runs at a linear speed of 45 km/h on 12-inch wheels. Preliminary center to center distance is 13”. This type of motorcycle requires two strands (conical double sleeve assembly) and is subjected to hard shocks. Can I get a detailed explanation for Choice of chain and sprocket. (Standard part number, see catalog)

Q: A polyamide A-3 flat belt 6 in wide is used to transmit 15 hp under light shock con- ditions where…

A: Solution:-Given-Driving pulley Diameter d=30 in-Driving pulley rotation M=1774 rpm-Driven pulley…

Q: For the following mechanism, Given: Lengths: O₂A=4 in, O3B=8 in, BC=5 in., O2O3-4 in. and offset…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: For the following mechanism, Given: • Lengths: O₂A-4 in, O3B=8 in, BC=5 in., O2O3-4 in. and offset…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: 5. For the flat spring shown below (Ball feed device), with L = 65mm, t = 0.8 mm and b = 6 mm.…

A:

Q: A1. A flat belt drive for speed reduction has pulley diameters of 200 mm and 380 mm. The maximum…

A: The diameter of pulleys = 200 mm and 380 mmThe maximum tension F₁ = 620 NThe power transmitted, P =…

Q: Refer to hoist system arrangement as in Figure Q1(b) and specifications details in Table Q1(b).…

A:

Q: ii) A five cylinder engine has a stroke of 180mm. The table below shows the lumped masses present at…

A:

Q: A generating set is arranged on board ship with its axis parallel to the longitudinal centre-line of…

A: We know, Gyroscopic couple is given asGivenr=180mv=36km/hr=mass of revolving part, m=1400kgradius of…

Q: A 500 pound weight is attached to a cable that is being lifted by a 10 inch diameter drum.  The 48V…

A: GIven data: The diameter of the drum is d=10 in The weight attached to the cable is Ft=500 lb The…

Q: 3)Design a V – Belt drive to the following specifications Power transmitted = 75kw Speed of driving…

A:

Q: Q2) A flat belt drive system is to be) designed for an application in which the input shaft speed is…

A:

Q: Lengths: O₂A-4 in, O3B=8 in., BC=5 in, O2O3-4 in. and offset c=10 in. Angles: 8-60° and -45° The…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: A hammer mill is driven by a High Torque (HT) AC motor. The system is used for 8 hours /day. Input…

A: Diameter of the motor shaft pulley = D1 = 1.33 cube root of Power / Speed max D1 = 1.33 cube root 25…

Q: Most gasoline engines in today's automobiles are belt driven. This means that the crankshaft, a rod…

A: The speed of smaller crankshaft is .The radius of smaller crankshaft is .The radius of larger…

Q: Please answer: 3, 4, 5, 6, 8, 9, 10, 12  The only correct answers are 1 (0), 2 (0), 7 (point A).…

A:

Q: Most gasoline engines in today's automobiles are belt driven. This means that the crankshaft, a rod…

A: The speed of smaller crankshaft is .The radius of smaller crankshaft is .The radius of larger…

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.