It is required to design a chaindrive to connect 5 kW, 1400 pmn electrie motorto a drilling machine. The speed reduction is3 : 1. The centre distance should he approximately500 mm.() Select a proper roller chain for the drive.(i) Determine the number of chain links.(iii) Specify the correct centre distance betweenthe axes of sprockets.

Given Power of the electric motor = 5 kW N = 1400 rpm Speed reduction = 3:1 To find Proper roller…

It is required to design a chain drive to connect 5 kW, 1400 rpm electrie motor to a drilling machine. The speed reduction is 3: 1. The centre distance should be approximately 500 mm. (i) Select a proper roller chain for the drive. (i) Determine the number of chain links. (iii) Specify the correct centre distance between the axes of sprockets.

It is required to design a chain drive to connect 5 kW, 1400 rpm electrie motor to a drilling machine. The speed reduction is 3: 1. The centre distance should be approximately 500 mm. (i) Select a proper roller chain for the drive. (i) Determine the number of chain links. (iii) Specify the correct centre distance between the axes of sprockets.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. Try to design a single reducer with a cylindered worm gear drive. Given the rated power of electric motor P=7.5KW, rotational speed n=1440r/min, speed ratio i=24(for reducing applications), uniform driven load, life expectancy 10 years, 16 hours per day, under unidirectional operating condition.
A chain drive is desired to couple a gearmotor with a bucket elevator. The 40 hp. gearmotor will operate at 350 rpm and the elevator drive shaft must operate as close to 60 rpm as possible. Select an appropriate chain size, commercially available sprockets, and number of links for a chain. Also calculate the actual chain speed and the center distance.
A mini motorcycle is driven by a combustion engine with mechanical transmission. The 12Hp motor spins at a speed of 1150 rpm. The motorcycle runs at a linear speed of 45 km/h on 12-inch wheels. Preliminary center to center distance is 13”. This type of motorcycle requires two strands (conical double sleeve assembly) and is subjected to hard shocks. a) Calculate the effective power.b) Choice of chain and sprocket. (Standard part number, see catalog)c) Calculate the speed ratio. https://pdf.directindustry.com/pdf/martin-sprocket-gear/general-catalog/9091-246439.html
Select a suitable Vbelt drive for a flour mill transmitting power from a motor of 10 kW rotating at 1,440 rpm using suitable charts. The mill rotates at 400 rpm for a service of 22hrs per day and is to be arranged in minimum space with center distance of 0.5m. Assume that the pitch diameter of small pulley is 100mm.
A 2hp motor is to drive a food shredder. The motor is projected to run at 1450 rpm and the required speed at the food shredder is 60 rpm. Design a double reduction drive consisting of belt and chain for this application. Please give solution and show drawing if needed
Do it
A hoist system load of 895 N at a velocity of exactly 1.2 ms'. If the motor efficiency is rated at 90% and the gearbox efficiency at 72% and the winding drum efficiency at 89%, calculate the power requirement of the motor. of your lecture notes) will be used to raise a
QUESTION 11 A motor-cycle engine crankshaft has an angular velocity of 523.6 rad/s and is in third gear of ratio 1.62:1. The final chain reduction is 4.7:1 and the effective wheel diameter 0.73 m. Calculate the road speed of the machine in km/h.
A mini motorcycle is driven by a combustion engine with mechanical transmission. The 12Hp motor spins at a speed of 1150 rpm. The motorcycle runs at a linear speed of 45 km/h on 12-inch wheels. Preliminary center to center distance is 13”. This type of motorcycle requires two strands (conical double sleeve assembly) and is subjected to hard shocks. Can I get a detailed explanation for Choice of chain and sprocket. (Standard part number, see catalog) https://pdf.directindustry.com/pdf/martin-sprocket-gear/general-catalog/9091-246439.html
gearing arrangement suitable for the given application is.
Question 1: A team of engineers from the Department of Mechanical Engineering are task to design a hoist equipment using a reverted epicyclic gear train shown in Figure 1. The drum must be keyed at the centre of the arm E using the same shaft. The pinion gear A is keyed to a second shaft which carries a chain wheel. Whereas the chain must be operated by hand. The two shafts have common axis but can rotate independently. The gear wheels B and C are compound and rotate together on a pin carried at the end of arm E. The gear wheel D has internal teeth and is fixed to the outer casing of the block so that it does not rotate. The wheels A and B have 16 and 36 teeth, respectively, with a module of 3 mm. The wheels C and D have a module of 4 mm. D- B E A- Figure 1: Top view of a reverted epicyclic gear train. 1.1. Draw the side view layout of the gear system to be designed. Clearly indicate the positions of all components. 1.2. Determine the number of teeth of wheel D. 1.3. Make use of the…
Note: If you don't know the solution please leave it but don't give me wrong solution. A flat open belt drive is used to transmit a power of 25kW from a motor shaft rotating at 950 rpm. The radius of the pulley of the motor shaft is 125mm while the radius of the puller of the driven shaft is 450mm. The center distance between the shafts is 2,250mm. the coefficient of friction is 0.25 and the density of the belt material is 950 kg/m^3. The belt width is 126 mm. The allowable stress is 2.6MPa. Determine the thickness of the belt.