A 10 pitch pinion with 20 teeth matos with a gear having 80 teeth The pinion rotates at 3,000 RPM. The gear pair is to be installod in a rectangular housing where a minimum of 0.20 in clearance botween the gears and housing is requirod. Specify the dimensions X and Y as shown in the figure bolow

A 10 pitch pinion with 20 teeth matos with a gear having 80 teeth The pinion rotates at 3,000 RPM. The gear pair is to be installod in a rectangular housing where a minimum of 0.20 in clearance botween the gears and housing is requirod. Specify the dimensions X and Y as shown in the figure bolow

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 15. A straight bevel gear pair has the following data: Np = 25; NG = 50: P, = 10: 20° pressure…

Q: Q 09. Consider a pair of 30° full depth involute spur gears having 20 and 40 teeth respectively and…

A: Find the addendum of smaller gear.

Q: The number of teeth on each gear so that interference is just avoided. The length of path and arc of…

A: Given: m=3 VR=3 pressure angle=20 Addendum=1m aw=1 To determine: Minimum number of teeth to avoid…

Q: The teeth of the gear arrangement have Gear A=40teeth, Gear B=70 teeth and Gear C= 50teeth, a pinion…

A: Given data: TA=40TB=70TC=50m=5 mm Need to determine the pitch diameter of the gear C.

Q: For the complex gear train shown, calculate the torque ratio (TR). W2 = @3 W4 130 rpm N, = 45 %3D N2…

A: Given data: The number of teeth in the first gear is N1 = 45. The number of teeth in the second…

Q: An 8-pitch pinion with 18 teeth mates with a gear having 64 teeth. The pinion rotates at 2450 rpm.…

Q: A 20 straight-tooth bevel pinion having 14 teeth and a diametral pitch of 4 teeth/in drives a…

A: Given Data: Number of teeth in Bevel pinion NP=14 Diametral pitch P=4 teeth/in Number of teeth in…

Q: The shaft rotating at 550 rpm carries a spur gear B having 96 teeth with a diametral pitch of 6 and…

A: Given data as per the question Speed of shaft =550 rpm No. of teeth on gear B =96 Diametral pitch =6…

Q: Two identical involute, spur gears are in mesh. The module is 4 mm and each gear has 22 teeth If the…

A: Given data: m=4 mmN=22ϕ=20° Need to determine minimum value of addendum needed to ensure continuous…

Q: wo spur gears are to have a ratio of 9:3 and a 7mm module. If the center distance is to be…

Q: Two mating spur gears have 40 and 120 teeth respectively. The pinion rotates at 1200 rpm and…

A: Given :- Two spur gear of Z1=40 teeth and Z2=120 teeth Pinion rotates at N1=1200 rpm Torque is…

Q: A 17-tooth 20° pressure angle spur gear rotates at 1800 rev/min and transmits 4 hp to a 52-tooth…

Q: A parallel helical gearset uses a 20-tooth pinion driving a 46-tooth gear. The pinion has a…

A: A) Normal circular pitch ( Pn). Pn= πP =π4= 0.785398in.Calculate the transverse circular path…

Q: A pair of helical gears are machined with a hob. The hob has a 20 degree pressure angle and machines…

A: The pressure angle = 20 degrees The circular pitch, p = 0.55 in/tooth the number of teeth on pinion,…

Q: A 17-tooth spur pinion has a diametral pitch of 8 teeth/in, runs at 1120 rev/min, and drives a gear…

A: Given data: The number of teeth on pinion is Tp = 17. The diametral pitch is Pd = 8 teeth/in. The…

Q: The 24T 6-pitch 20° pinion 2 shown in the figure rotates clockwise at 900 rev/min and is driven at a…

A: Given Data: Speed of the 24T 6-pitch 20° pinion 2 is 900 rev/min clockwise. Power at which pinion…

Concept explainers

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.

Question

A 10 pitch pinion with 20 teeth mates with a gear having 80 teeth The pinion rotates at 3,000 RPM. The gear pair is to be installed in a
rectangular housing where a minimum of 0.20 in clearance botween the gears and housing is requirod. Specify the dimensions X and Y
as shown in tho figure below
Note: This question requires a file attachinent, which can be pdf, ipeg. word, excol or power point.
Show all your calculations. Handwritten calculations are acceptable.
0.20 in
0.20 In
0.20 in
GEAR
PINION
N, 20

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Design of Power Transmission Elements and Power Transmission Systems

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Provide the complete step-by-step solution, given data, conversion of units, and sketch for this problem. A turbine at 30,000 rpm is used to drive a reduction gear delivering 3 hp at 3,000rpm. The gears are 20 degrees involute herringbone gears of 28 pitch and 2 1/8 ineffective width. The pinion has 20 teeth with a helix angle of 23 deg. Determine theload normal to the tooth surface. A. 20.4 lbs B. 24.4 lbs C. 28.4 lbs D. 32.4
Please use the following table and please the ratio is not 1.714 this answer is wrong. Please don’t reply with same answered way previously!!!!
A simple gear train of 30 and 50 teeth for pinion and gear wheel respectively,is used to drive an electric wheelchair at a velocity that is double the maximum velocity of slip. The pinion has an equal addendum as the gear wheel, a module of 3 mm, and a pressure angle of 14.5o. The wheelchair has a maximum velocity of 5 m/s when its pinion rotates at 800 r.p.m. Calculate: 1.1. The magnitude of the velocity of slip of gears in mesh. (2)1.2. The angular speed of the gear wheel in rad/s. (4)1.3. The maximum length of a path of the approach in mm. (2)1.4. The length of a path of a recess in mm. (7)1.5. The addendum of the gears in mm. (7)1.6. The contact ratio.
Q2/ Two mating involute spur gears of 20* pressure angle have a gear ratio of 2. The number of teeth on the pinion is 20 and its speed is 250 r.p.m. The module pitch of teeth is 10 mm. If the addendum on cach wheel is such that the path of approach and the path of recess on cach side are half the maximum possible length each, find: i) the addendum for pinion and gear wheel, ii) the length of arc of contact, iii)the maximum velocity of sliding during approach and recess. Assume pinion to be driver.
i need the answer quickly
A 17-tooth pinion meshes with an 84-tooth gear. The full-depth involute gear teeth have 20° pressure angle and a diametral pitch of 32. Determine the base pitch and the contact ratio. Also,calculate the addendum, dedendum, circular pitch, tooth thickness, and the base diameter for the pinion and gear. If the center distance is increased by 0.125 in., what are the new values for the contact ratio and the pressure angle?
A parallel helical gearset consists of a 21-tooth pinion driving a 63-tooth gear. The pinion has a left-hand helix angle of 20°, a normal pressure angle of 14 1/2, and a normal diametral pitch of 10 teeth/in. Find: (a) The normal, transverse, and axial circular pitches (b) The transverse diametral pitch and the transverse pressure angle (c) The addendum, dedendum, and pitch diameter of each gear Attach File Browse My Computer
A similar pair of helical gears , also on parallel axes, are to have involute teeth, of 20o normal pressure angle, and 3 mm normal module. The wheels are to have 26 and 34 teeth, and to work with a centre distance of 146 mm. Calculate the transverse pressure angle in degrees.
i. A parallel helical gearset uses a 20-tooth pinion driving a 46-tooth gear. The pinion has a righthand helix angle of 30•, a normal pressure angle of 20•, and a normal diametral pitch of 6 teeth/in. Find: (a) The normal, transverse, and axial circular pitches (b) The normal base circular pitch (c) The transverse diametral pitch and the transverse pressure angle (d) The addendum, dedendum, and pitch diameter of each gear
A pinion having 40 teeth is meshing with a spur gear having 80 teeth. The profile of the gear is involute. The module of the gears is 12 mm and pressure angle is 20 degree. The addendum of the gears is 10 mm. Find the length of path of contact, arc of contact and the contact ratio.
Please answer the question in details
Answer d and e