The figure illustrates the nonpermanent connection of a steel cylinder head to a grade 30 cast-iron pressur vessel using 73 bolts. A confined gasket seal has an effective sealing diameter D of 0.9 m. The cylinder pressure is cycled between a minimum pressure of zero and a maximum pressure Pg of 535 kPa. For the specifications given in the table for the specific problem assigned, select a suitable bolt length from the preferred sizes. Use Table A-17 for calculation purposes. Parameter Value Head thickness, A Cylinder thickness, B Internal diameter of the cylinder, C 16 mm 25 mm 0.8 m 0.9 m Gasket sealing diameter, D Bolt circle diameter, E Outer diameter of the cylinder head, 1.0 m 1.1 m Bolt grade Bolt diameter, d ISO 10.9 10 mm NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. -D 早

The figure illustrates the nonpermanent connection of a steel cylinder head to a grade 30 cast-iron pressur vessel using 73 bolts. A confined gasket seal has an effective sealing diameter D of 0.9 m. The cylinder pressure is cycled between a minimum pressure of zero and a maximum pressure Pg of 535 kPa. For the specifications given in the table for the specific problem assigned, select a suitable bolt length from the preferred sizes. Use Table A-17 for calculation purposes. Parameter Value Head thickness, A Cylinder thickness, B Internal diameter of the cylinder, C 16 mm 25 mm 0.8 m 0.9 m Gasket sealing diameter, D Bolt circle diameter, E Outer diameter of the cylinder head, 1.0 m 1.1 m Bolt grade Bolt diameter, d ISO 10.9 10 mm NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. -D 早

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The figure illustrates the non-permanent connection of a steel cylinder head to a grade 30 cast- 8-35 iron pressure vessel us
the shaft and Bols bolts. [Ans. 300 mm; 56 mm] 11. Design a bushed-pin type flexible coupling for connecting a motor shaft to a pump shaft for the following service conditions: Power to be transmitted = 40 kW; speed of the motor shaft= 1000 r.p.m. ; diameter of the motor shaft = 50 mm ; diameter of the pump shaft = 45 mm. The bearing pressure in the rubber bush and allowable stress in the pins are to be limited to 0.45 N/mm2 and 25 MPa respectively. [Ans. d, = 20 mm; n 6; d, = 40 mm; 1 152 mm] :1.1
8. Design a clamp coupling for transmitting 25 kW at 300 rpm. Allowable shear stresses in shaft and key are 50 MPa and 45 MPa, respectively. The number of bolts joining the two halves of muff is 4. The permissible tensile stress in the bolt is 70 MPa and the permissible crushing stress in the key is 90 MPa. The coeffi cient of friction between the muff of the CI and the shaft of steel is 0.20.
As shown in figure below, two plates are clamped by washer-faced 2 in-20 UNF SAE grade 5 bolts each with a standard 2 N steel plain washer. The top plate is steel and the bottom pplate is gray cast iron. If a total of 8 bolts where used to close 1 feet diameter pipe which applied at maximum pressure of 150 psi. Calculate the static and fatigue safety factor of this joint. Used Goodman theory for tha fatigue safety 1/2 factor. 3/4
Design and draw a neat sketch of a cast iron protective type flange coupling to transmit “P” kW at “N” rpm. from a turbine generating n electric motor to a compressor. The service factor may be assumed as 1.35. The following permissible stress may be used: Shear stress for shaft, bolt and key material = 40 MPaCrushing stress for bolt and key = 80 MPaShear stress for cast iron = 8 Mpa Speed N in Rpm = 200Power P in kN = 16
Calculate the maximum tensile stress developed in a 1/4-20 bolt (Major dia = 0.2500" and Root dia = 0.1959"), 3" long, and a head height of 0.1875", if it is subjected to a load of 426 lbs.
Find the size of 14 bolts required for C.I.steam engine cylinder head. The diameter of the cylinder is 400 mm and the steam pressure is 0.12 N/mm.
A link in a mechanism is to be subjected to a tensile force that varies from 3500 to 500 N in acyclical fashion as the mechanism runs. It has been decided to use AISI 1040 cold-drawn steel.Complete the design of the link, specifying a suitable cross-sectional shape and dimensions.5. Specify the required length of no. 60 chain to mount on sprockets having 15 and 50 teeth with acenter distance of no more than 36 in.
3. An M16 x 2 bolt with a slotted hex nut is used to clamp together two 25 mm steel plates. The joint is assembled with a size 16 N washer underneath the bolt head. The bolt is a 5.8 class metric grade, with a proof strength of 380 MPa. The joint is intended to be permanent. Determine a suitable length for the bolt, rounded up to the nearest standard size in millimeters. Calculate the bolt stiffness, the elongation of the bolt after the necessary preload is developed, and the bolt torque required to apply the preload. Assume that coefficients of friction between the bolt, nut, and collar are all ~0.15. For steel, use E = 207 GPa. Standard threaded fastener lengths, dimensions of hexagonal nuts, and dimensions of metric plain washers are provided in the textbook appendices.
6. Design a clamp coupling for transmitting 36 kW, at 200 rpm. Allowable shear stress in shaft is 45 MPa, allowable shear stress in key is 40 MPa, and allowable crushing stress in key is 90 MPa. The number of bolts joining the two halves is 4. The permissible tensile stress in bolts is 60 MPa. The coefficient of friction between the muff and shaft can be taken as 0.25
Calculate the dimensions of the I-section of a connecting rod, stating any assumptions. using the data below: Maximum cylinder pressure = 3.15N/mm² Cylinder bore = 100mm Factor of Safety=6 Crank length 95mm Connecting rod length=380mm Take the constant a=7500.
The value of curvature correction factor k, will be if the spring index is 6. O a. 1.33 O b. 1.08 O c. 0.92 O d. 4.00 The figure below shows the components of normal forces, the value of radial force on the gear wheel due to a tangential force of 642 N is N, Take pressure angle as 14½0. at Pitch P. point Gear driven to 02 The radial force is