The maximum bolt preload that can be applied is) Ibf.

Q: . The relationship between sizes of mating parts is called ______ ______.

A: According to the study the relationship between the assembly part with respect to their actual size…

Q: Question 1 Compute the lead of a 4 -19 UNC single t

A:

Q: It asks what is the width across the flats of the locking bolt head?

A: The width across the flats of the locking bolt head is 0.5625

Q: The indicator needle on a speedometer is heldto the zero position by ___.a. magnetic forceb. the…

A: A sort of tachometer is a wheel speed sensor, often known as a vehicle speed sensor (VSS). It's a…

Q: This part of the a cylinder holds the piston in place and helps support the rod as it extends. a.…

A: Option c is correct.

Q: Which of the following is the most common method of snug tightening bolts? O Heat tightening O…

A:

Q: A/Two plates to be fastened by means of bolt thickness of plate 50mm use a bolt of dimension…

A: Given Data: The thickness of the plate, t=50 mm

Q: What does the internal moment cause?

A: Internal moment are actually the moments due to the resisting forces generated when the cross…

Q: -) Draw free hand and proportionate sketches for any four of the 1- Pan and rounded countersunk head…

A: Rivets are used for the fixing of two or more objects. Different types of rivets used in engineering…

Q: Technician A says that a micrometer can be used tomeasure the outside diameter of something.…

A: Micrometers exist in a variety of forms, depending on what they're used for. An exterior…

Q: choose true or false : -The speed of the sprocket reduces as the chain pitch increases for a given…

A: The speed of the sprocket reduces as the chain pitch increases for a given number of teeth.

Q: 13. When tightened, dry seal threads A. are crushed to make a leakproof seal. O B. compress an…

A: According to t the question We need to explain the problem  13,14 and 15

Q: what is true in the lever arm below? a. it is unstable b. statically determinate but unstable c.…

A:

Q: 5 ft 2 ft 7 ft The train has a weight of 23000 Ib and a center of gravity at G. It is suspended from…

A: Free Body Diagram for the given condition can be made as shown below: All normal reactions are…

Q: What is the pitch diameter for an M24 fine-series threaded bolt? O 21.5 mm

A: What is the pitch diameter for an M24 fine-series threaded bolt?

Q: Find the natural constraints for the turning crank shown below. CÂ cŷ

A: to find:the number of natural constraints.given:the figure

Q: What is center of percussion? Write down Procedure for finding COP of a wooden compound pendulum

A: Given;To define contre of percussionTo write procudure for finding COP  of a wooden compound…

Q: Fulcrum can be only  located at one end of the lever.

A: Fulcrum can be only  located at one end of the lever.

Q: 1. Draw a FBD for the cylindrical tub before the metal object is added, clearly labeling all forces.…

A: When a body is immersed in water , the following forces acts on the body  1) Weight of the body  2)…

Q: Worn teeth on a speed gear can cause?

A: worn teeth creates a big problem in gear drive.

Q: The rotation angle of the joints is still needed.

A:

Q: голь 40° Find P. do, 25°

A:

Q: CG 50 in 75 in A=? B=100 lbs C=100 lbs

A:

Q: True or False? The largest diameter threaded rod is available only up-to 8-inches

A: The threaded rod has several different measurements associated with it. There is major diameter,…

Q: Which type of joint has a flatter design than anyother?a. Double-offsetb. Discc. Cross grooved.…

A: The cross groove joint uses balls and V-shaped grooves mostly on inner and outer races to cater the…

Q: Design for 95% male grip force. Use a minimum factory of safety of 2.50. Determine dimensions not…

A: By using the above data and some engineering principles, we can calculate the value of dimension C…

Q: Identify the part not belonging to micrometer. Ratchet Clamp O Locknut Frame

A: Given :-  Identity the part not belongung to micrometer Ratchet  Clamp  Locknut Frame

Q: Draw three views of the adjusting bracket. . Orill-2 Holes 3 BOrill

A: The figure below shows the top and front view of the given model.

Q: Design a piston for use in automobile engines (piston ring, pin, skirt).

A:

Q: Need help drawing a 1/2-13 UNC 2A Hex head bolt

A: THIS HOW IT'S GONNA BE

Q: 7. How many ½ inch diameter set-screws would be required to transmit 3 horsepower at a shaft speed…

A:

Q: hat is the increment of the 3 cylinders?

A: When we increase the number of cylinders in a vehicle, the power and performance of the engine both…

Q: What is the LMC of shaft C?

A: The Least material condition (LMC) tells about the minimum material can be used to produce the…

Q: 20 BUTT-2A .688 R. .626 DIA..003 5.50 13 812 6.000 -1.000 UNLESS OTHERWISE SPECIFIED: MATERIAL:…

A: 5. Pitch  6. BUTT is designation for  9. Standard or precision class of fit

Q: If you use a generator and gear box with high efficiency, the power output of the Wind turbine will…

A: Required :- To state whether the given statement is true or false

Q: If the arc of contact of a gear is is 34 mm and the radius of the gear is 80 mm then what will the…

A: Given data: -  The arch of contact is Aoc = 34 mm. The radius of the gear is r = 80 mm.

Q: Using Free Hand Sketch, Draw the Three Views for Tow of the following bodies.

A: Please refer the below images for the required free hand sketches.

Q: Describe the Procedure for Using Automatic Hammer.

A: It’s a commonly used method in industry. A basic hammer comprises 5 parts as shown in the figure.…

Q: Define Iron Stirrups

A: Given Stirrups To find Iron stirrups

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.